Q.I A line of level is run from B.M.1 (elevation-106.40m) to B.M. 2(clevation-110.50m). The field observations were recorded as given below: B. S 1.95 Station I.S F.S Remarks В.М. 1 2 0.65 3. 2.60 1.45 4. 1.90 -1.60 5 0.55 6. 0.50 В.М. 2 Reduce the level of point 2, 3, 4 and 5, determine the total error of closure, and adjust the values.

Q.I A line of level is run from B.M.1 (elevation-106.40m) to B.M. 2(clevation-110.50m). The field observations were recorded as given below: B. S 1.95 Station I.S F.S Remarks В.М. 1 2 0.65 3. 2.60 1.45 4. 1.90 -1.60 5 0.55 6. 0.50 В.М. 2 Reduce the level of point 2, 3, 4 and 5, determine the total error of closure, and adjust the values.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Adjust the quadrilateral using angle condition and side condition equation
problem #3
Example - 3: Following readings were taken with level. 1.155, 1.565, 2.695, 3.580, 2.085, 2.895, 4.125, Level was shifted after fourth reading. Calculate R.L. all points by H.I. method. Apply check. R.L. of B.M. iş 50.0 M.
What is the elevation at station TP3 A. 127 B. 127.45 C. 123.1 D. 124. 13 E. 124.77
PROBUEM 2. Gven: F: 45ON 6: 36ON Find : mc MA , MB, ME ME I 3, F 2m
provide the leveling illustration for the given values below
Solve all questions. with explanation
In carrying out the permanent adjustments of a level by, the following observations were made: Instrument at peg (C) midway between points A and B, 100m apart. Readings at points A and B are 2.500m and 3.500m, respectively. Instrument at peg (D) in line of AB such that AD-120m and BD-20m, Readings at points A and B are 1.500m and 2.600m, respectively. Check whether the instrument needs permanent adjustment or not and whether the line of sight is inclined upward or downward. What should be the correct reading at (A and B) if the instrument is to be adjusted?
A 500 mm x 500 mm square tied column shown is reinforced with 10- 26 mm diameter bars with a steel covering of 62.5 mm from the center of the bars to the outer edge of the column section. fc' = 20.7 MPa, fy = 345.6 MPa, e = 421.4 mm. (DO NOT USE CID) a) What is the value of the depth of the compression block, "a" X Soomm 62.5mm 62.5mm 500mm e Pn
Solve correctly please, will provide helpful ratings for correct solution.
A constant head orifice from a tank feeds water into a flume (open channel) 5m in length and 500 mm wide with a rectangular contracted weir (L=200mm) at one end and close at the other end. The orifice diam is 80mm, coef of discharge=D0.92, and a head h=1m. a) Find the maximum head H of the weir. b) If the supply from the orifice is closed, find the time to lower the head of the weir by 80mm. c) Find the total time for the flow in the weir to stop after closing the supply of water from the orifice.
Solve correctly please.