q (kN/m) B A + -6 m- -3 m- a) Determine the support reactions. b) Calculate for the maximum bending moment. c) Draw the shear and moment diagram (specify magnitudes at indicated points A, B, C, etc.) V P (KN) C

Q: can you explain why in solving for d the 2.5in was divided by 2

A: Given:- The overall depth of the beam = 30 in The concrete cover = 2.5 in  To determine:- Why for…

Q: a = 6.1 m, b = 4.1 m, c = 14.1 kN/m, d = 24 kN. d kN d kN c kN/m "b" m "b" m FIGURE 3

A:

Q: 150 kN 50 kN/m E C D 21

A:

Q: 3. Determine the slope and vertical displacement of point A on the beam shown in the accompanying…

A:

Q: answers should be 3 decimal places A particle is moving along a curved path. At a certain instant…

A:

Q: Figure a d 1 of 1 Locate the centroid y of the channel's cross-sectional area. Set a = 6 in., b =…

A:

Q: Using the double integration method, find the following unknowns on the beam depicted below. With E…

A: E = 200 GPa Beam size = 250mm × 450mm Determine1. Deflection at B in millimeters.2. Deflection in…

Q: For the structure shown in Figure, apply virtual work to calculate  i) the vertical deflection at…

A:

Q: The quarter cylindrical gate AB has a radius of 1.5 m and length 3 m perpendicular to the paper. It…

A: Given: Radius of gate = 1.5 m  Length perpendicular to paper = 3m Required: Horizontal component of…

Q: R

A:

Q: need

A:

Q: Situation 4: A W6x25 has a length of 5.3 m. Fy= 248 MPa. The properties are given below. Properties…

A: Le = kL = 0.8 x 5.3 m = 4.24 m = 4240 mm

Q: solve accurately with steps

A: Answer- I have given hand written step by step solution in the explanation box. Explanation:Step…

Q: Problem 2. A 30 m steel tape weighing 14.23 N is of standard length under a pull of 7 kg, supported…

A:

Q: Determine the slope at point C measured counterclockwise from the positive a axis. Use the principle…

A:

Q: A continuous beam loaded as shown figure. Assume El is constant. Use any method to determine the…

A:

Q: A 30 m steel tape weighing 1.45 Kg is of standard length under a pull of 5 Kg,supported for full…

A:

Q: 3 k/ft A 20 ft Given: E= 290 x 106 psi, I = 1500 mm¹ Use Double Integration Method to determine the…

A:

Q: Problem 4: Kinetic Head no picture necessary Use the Rayleigh Method to show that velocity head is…

A:

Q: Structural Analysis The cantilever beam carries load as shown in the figure below. Compute the…

A:

Q: PROBLEM 1 A cantilever beam carries a varying load as shown in the figure. If E=200,000 Mpa and…

A: The length of span,L =6.5mThe modulus of elasticity of beam, E =200000 MPa.The moment of inertia of…

Q: It takes a vertical force of F= 75,000 lb to separate the two parts at A and C in (Figure 1). Figure…

A: Given, F=75,000 lbμs=0.2to determine,P

Q: The waterline section of a barge is as shown. a) Calculate the total area (m^2) of the…

A: Given :

Q: Solve it By slope deflection method

A:

Q: In figure, Bernoulli's equation- ?between point 1 and 2 is 50m Pump Lake

A:

Q: Solve for the value of R and X that will make the bar in equilibrium. *use 3 decimal place in…

A: Take equilibrium about vertical:∑ Fy=0R+1.5R-50x-305-300-250=02.5R-50x=700R=280+20x........1

Q: PROBLEM THEORY-10. A 4-m propped cantilever beam is loaded as shown in the figure. E = 200 GPa and I…

A:

Q: The simply supported beam carries three concentrated loads as shown in the figure. Determine the…

A:

Q: Determine the force in each member of the structure and establish whether the members are in tension…

A:

Q: 2. The vertical steel bars BE and CF supports the horizontal rigid bar ABCD and the applied forces…

A:

Q: 2. Derive an equation that describes the vertical deflection of the beam, y(x), and also calculate…

A:

Q: Exercise 1: Calculate the horizontal displacement and the slope at C. -10x10 cm? 2 KN E = 200 GPa…

A: Virtual method is used to calculate deflection at any point in a member.In this method a unit load…

Q: P= 1.60 ton q= 1.30 t/m (El = 5050 t.m²) B 2.10m

A: Given data  Cantilever  Span length  UDL Point load Flexural rigidity

Q: then the total displacement

A: FALSE

Q: In the tigure shown, El is contant. Determine the Momernt at CB, Mcs in kNim 100 KN 50 kN/m 5m 3m 3m…

A:

Q: ◆ Problem 7 Derive the following weight-volume relationships. If required, clearly state assumptions…

A:

Q: Q=0.012 m/s Q1) The water jet impinges an inclined flat plate as shown in Figure (1). Find: 1.…

A:

Q: In the figure, a small 0.309 kg block slides down a frictionless surface through height h = 0.478 m…

A: Step 1:

Q: A solid sphere made of aluminum (SG = 2.7) is suspended in water by a cable. The cable has a tension…

A:

Fluid Materials

In general terms, anything that flows can be termed as a fluid. In other words, a fluid is any substance that cannot resist shear forces and deforms continuously under the application of external shear forces. Fluid materials differ completely from solid materials such as metals and alloys. For instance, if we consider two infinitesimally small cross-sectional areas of fluid materials and solid materials, and apply shear forces to these elements, both the elements will undergo deformation. Upon releasing the shear force, the element of the solid materials will regain its original orientation, but the element of the fluid materials will keep on deforming continuously under the action of the shear force.