Problem Direct stresses of 120 N/mm² tensile and 90 N/mm² compression exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stress on the planes. The greatest principal stress at the point due to these is 150 N/mm². (a) What must be the magnitude of the shearing stresses on the two planes? (b) What will be the maximum shearing stress at the point?

Problem Direct stresses of 120 N/mm² tensile and 90 N/mm² compression exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stress on the planes. The greatest principal stress at the point due to these is 150 N/mm². (a) What must be the magnitude of the shearing stresses on the two planes? (b) What will be the maximum shearing stress at the point?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At a point, the normal and shear stresses acting on one plane are 8,000 psf compression and 2,000 psf, respectively. On a perpendicular plane, the normal and shear stresses are 2,000 psf compression and 2,000 psf, respectively. (a) Draw the Mohr’s circle. (b) Determine the value of the principal stresses. (c) Find the angle between the plane on which the 8,000 psi compressive stress acts and the major principal plane. (d) What is the maximum shear stress acting at the point?
The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both compressive, along with a shear stress of 80 MPa. What is the normal stress on a plane inclined at 30° to the plane of 160 MPa stress? (a) -42.4 MPa (b) -75.7 MPa (c) -59.1 MPa (d) -86.3 MPa
es A state of stress at a point is the result of two separate actions; one produces the pure shear of 35 MPa shown in figure A and the other produces the pure shear of 30 MPa shown in figure B. 35 MPa -19.86 degrees Y -17.04 degrees -X Figure A Which of the following most nearly gives the principal planes for the combined state of stress? Select the correct response: 35 MPa 30° Figure B 30 MPa 30 MPa 4
A type of stress tangential to the area on which it acts; direct stresses, however, are always normal to the area on which they act. A) shear stress B Torsional Stress Normal Stress Flexural Stress
2. In the structure below, the vertical bar A has a modulus of elasticity of 210 GPa, a length of 475 mm, and a cross-sectional area of 260 mm². The post B has a modulus of elasticity of 14 GPa, a length of 450 mm, and a cross-sectional area of 5300 mm². The rigid bar CDE is horizontal before the load P = 222 kN is applied. Determine a) b) The axial stress in the vertical bar A and post B; The deflection at point D. C Smooth A pins 480 mm D 870 mm P E B
Solid mechanics
Calculate the principal strain.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 44 MPa in the direction shown, determine the principal stresses at the point. 85 MPa 56 MPa O 70.9 MPa and -97.0 MPa 82.8 MPa and -136.0 MPa 89.5 MPa and -64.2 MPa 75.1 MPa and -124.1 MPa 64.9 MPa and -105.9 MPa
Determine the force required to produce stress of 20 N/m2 on cross sectional area of 5 m2
The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both compressive, along with a shear stress of 80 MPa. What is the normal stress on a plane inclined at 30° to the plane of 160 MPa stress? (a) -42.4 MPa (b) -75.7 MPa (c) -59.1 MPa (d) -86.3 MPa
pls help me answer my homework. thank you.
If the combination of normal and shearing stresses acting on any two mutually perpendicular planes (orthogonal planes) is known, through this what can be determined?