Problem 6 A 34.5 ft diameter by 48.3 ft height vertical tank is receiving water (p= 62.4 lb/ft ³) at a rate of 208 gpm and is discharging through a 8 -in inside diameter with a constant speed of 7.46 fps. At a given instant, the tank is half full. Find the water level and the mass change in the tank 48 min. later. Solution 208 gpm 48.3. 34.5 7.46 fps I 24 -24.15

Problem 6 A 34.5 ft diameter by 48.3 ft height vertical tank is receiving water (p= 62.4 lb/ft ³) at a rate of 208 gpm and is discharging through a 8 -in inside diameter with a constant speed of 7.46 fps. At a given instant, the tank is half full. Find the water level and the mass change in the tank 48 min. later. Solution 208 gpm 48.3. 34.5 7.46 fps I 24 -24.15

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hello, can I get help please?
Fluid
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The suction pipe is 350mm in diameter and 12m in length, and the delivery pipe is 550mm in diameter and 40m in length. The friction factor of the pipe system is f=0.005. Q. Calculate the maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa
subject: hydraulics engineering
Water flows through a pipe AB withm diameter andm/s then passes through pipe BC with diameter. The flow in branch CE is AB (in cubic meter/second), the velocity (in meter/ second) in BC and CD and the diameter (in meter) of CE if CD is m/s. Find the volume rate in m in diameter and carries 1/3 of the flow in AB. 0.8 m B. 1.2 m 1.5 m VAB- 3 m/sec Q2 E VoE 2.5 m/sec
3. Medium lubricating oil (sg=0.85) is pumped through 360m of horizontal 75mm pipe at the rate of 3.14L/S. If the drop in pressure is 300kPa. Compute for the absolute viscosity in Ns/m2 of the oil. a. 0.311 b. 0.206 c. 0.504 d. 0.790
A pump is discharging 12 lit/sec ofwater through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assumingf= 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 2 45 m 540m - 100mm dia
Water at 100 kPa flowing in a 10-cm-diameter pipe passes through a 2-cm-diameter flow nozzle equipped with a manometer across the nozzle. 10 cm 8 cm S = 10 12 cm S- 13 16.0 Determine the flow of water through the nozzle if coefficient of discharge is 0.7 a.) 1498 mL/s b.) 1433 mL/s c.) 4488 mL/s d.) 4539 mL/s e.)
An open tank with piezometers attached on the side contains two different liquids.Determine the elevation of the liquid in piezometer Achoices are:A. 2.2mB. 2mC. 2.4mD. 2.1m Find the pressure at the bottom of the tankchoices are: A. 18.59 Kpa B. 18.85 kPa C. 19.85 kPa D. 18.95 kPa Find the elevation of the liquid in piezometer Bchoices are: A. 0.918m B. 0.819m C. 0.189m D. 0.889m
Mato 5
Q1(b) Water flows through a pipe with a diameter of 2 m. Stagnation and static pressures measured by pitot tube are 0.3 m and 0.25 m of water, respectively. Calculate the velocity of flow
Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe length is 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should be the different in elevation between the upper and lower levels in order to achieve this pressure? Take the density of water 1000 kg/m3 and gravity is 9.81 m/s2, consider the energy loss.