Problem 1. A tape of standard length 20 m at 85°F was used to measure a base line. The measured distance was 850.50 m. Given the slopes for the various segments of the line, calculate the true length of the line if the mean temperature during measurement was 63°F and the coefficient of thermal expansion of the tape material is 6.5x10-6 /°F.

Problem 1. A tape of standard length 20 m at 85°F was used to measure a base line. The measured distance was 850.50 m. Given the slopes for the various segments of the line, calculate the true length of the line if the mean temperature during measurement was 63°F and the coefficient of thermal expansion of the tape material is 6.5x10-6 /°F.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need a handwritten solution, Thank you..
III. PROBLEM SOLVING 36. To measure a base line, a steel tape 30 m long, standardised at 15° C with a pull of 80 N was used. Find the correction per tape length, if the temperature at the time of measurement is 25° C and the pull exerted is 150 N. Take Young's modulus E = 2 × 10^5 N/mm2 and coefficient of thermal expansion a = 11.2 × 10^6/°C. Cross-sectional area of tape is 8 mm2.
Can someone explain where the 32.2 is coming from please
Answer in three decimal places
Compute the kinematic viscosity of a R ft long model of ship when the prototype ship length is 500 ft and is travelling with a speed of 20mile per hour in an ocean whose viscosity is 1.2 cP and specific weight is 64 lb/ft3 . Keeping in mind to satisfy the condition that both the Reynolds number and the Froude number should be same. (R is 39)
A tape of 20m length is used to measure a distance 1980 m at a temperature 35 °C oumale borte under 20 N tension force, find the correct measured distance if: down: STEFTICAGES Standard temperature20 °C Coefficient of thermal expansion 11.6*10 Mass of tape is 0.04 kg/m Standard tension 60N Cross section area of tape 2mm² Modulus of elasticity of tape 2000000 kg/cm²
to measure a base line, a steel tape 30m long standardised at 15 degree Celsius with a pull of 100N was used. Find the correction per tape length, if the temperature at the time of measurement was 20 degree Celsius and the pull exerted was 160N weight of 1cm3 of steel is 0.0786N and weight of the tape=8N, E=210000kg/m2, coefficient of expansion of tape per 1 degree celsius is 0.00000071.
Mean size represents in a sieving analysis: O 80% of the finer, which is smaller than the particles with biggest density bulk O 50% of over size which, is smaller thana specific particle size 50% of the finer which, is bigger than a specific particle size Represents 50% of the smallest particie size. O 50% of the finer, which is smaller than the particles with biggest density real. O 50% of over size which, is bigger than a specific particle size. O 50% of the finer, which is smaller than the particles with biggest density bulk O Represents 50% of the biggest particle size. O 80% of over size which, is bigger than a specific particle size O 80% of the hiner, which is smaller than the particles with biggest density real
Question #1 A hole having a diameter of 75 mm is cut out from a uniform plate of diameter 240 mm. The distance between the center of the plate and center of the hole is 50 mm. Determine the position of the center of gravity of the remaining material.
A line was found out to be 2865.35 m long when measured with a 30-m tape under a steady pull of 6.5 kg at a mean temperature of 30 degC. Determine the correct length of the line if the tape used is of standard length at 20 degC under a pull of 5.5 kg. Assume that the cross-sectional area of the tape is 0.025 cm², elastic modulus of tape is 2.10 x 106 kg/cm? and coefficient of linear expansion of steel is 11.6 x 106 per degC.
A 1200 Ibs force acts as shown on a 500 Ibs block placed on a horizontal plane surface. Determine the following: a. Coefficient of friction between the block and the plane surface. b. Determine whether the block is in equilibrium, and find the value of the friction force. If the Coefficient of friction between the block and plane surface are us = 0.30 and Hx = 0.25. 500 lbs 62°- 1200 lbs