Please include complete solution and diagram if possible.

Q: Which one of the following is the most economical store design? a. Geometrical layout b. Angular…

A: the correct answer is option c - straight floor layout

Q: What is the overall density? %

A: This question is related to the Soil Mechanics from Civil Engineering.

Q: Define PDOP?

A: PDOP ( Position dilution of precision) It describes the error caused by the relative position of the…

Q: Define Land Drainage.

A: Drainage is a reverse method of irrigation  This is generally known as the removal / disposal of…

Q: Explain the step-by-step process of the methodology for lot area sketch plan preparation. Give…

A: The lot area sketch plan A lot area sketch plan is a rough drawing that shows the layout of a piece…

Q: When preparing a written report (which includes survey report, description, and sketch), the shall…

A: ASKED: To choose the correct option corresponding to the given statement.   Given statement: When…

Q: Define Bearings?

A: Bearing: It is defined as the angle which is measured between the reference meridian and the survey…

Q: Design a typical layout model for a Water Supply Scheme

A: Brief Concept- Water Supply Scheme- It is the set up of different units for the treatment of water…

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: (b)       Define Bench Mark. List down its different types

A: A benchmark is a reference point that helps one to calculate something. A "bench mark" associated…

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: Who keeps the design or site information in their possession?

A: The life cycle of the project can be defined as a mechanism by which a project is carried out from…

Q: Give a brief description: a. Measurement of Horizontal Distances b. Omitted Measurements c.…

A: Any plane which contains horizontal line and perpendicular  to the vertical direction is called as…

Q: Compute total indeterminacy

A: Given data : Number of external support reaction (R)=2+2+2=6 Number of member attach at hinge joint…

Q: Please fill in the blank for this question please! A *blank* call identifies a corner or boundary,…

A: A _________call identifies a corner or boundary, usually as some object that constitutes the…

Q: List the different meridians are used to specify directions?

A: The direction of a survey line can be defined in two ways: Relative to each other  Relative to some…

Q: derivation of the formulas used in every section

A: This question has been taken from fluid mechanics

Q: Find and define " horton equation" Show illustration.

A: To find and define Horton equation.

Q: Factors for planning include

A: before starting any project you need to do proper planning by using previous record , test…

Q: The beam with three supports carries a uniformly distributed load. Determine all the support…

A:

Q: actors that cause hardness along with a bibliography

A: The water hardness may be simply defined as the amount of dissolved calcium and magnesium in the…

Q: CAD system to generate the final schematic

A: Computer aided design is the technology of designing,analyzing and modifying a structure before and…

Q: SANITARY PLANNING LAYOUT " F. SYMBOLS AND LEGENDS

A:

Q: Give a detailed explanation and steps of the methodology of lot area sketch plan preparation.

A: The methodology for preparing a lot area sketch plan typically includes the following steps:…

Q: Define Soil conditions.

A: Soil condition:

Q: What is a site plan? Discuss it. (M Please cite reference as per APA

A: A site plan is a detailed drawing that shows the area where the building has to be constructed…

Q: classification of rivers

A: Classification of Rivers

Q: 7. Usually the minimum height in the room should not be lower than ( A. 2.2 m B. 2.0 m C. 2.4 m…

A: Note: Multiple questions are asked. Therefore, as per Bartleby guidelines, the answer of only…

Q: Q#4: Define Baseline, Main survey line, check line and tie line?

A: - Baseline, main survey line, check line and tie lines are mostly used in triangulation surveying to…

Q: What is the difference between primary standards  and secondary standards in AAQS?

A: Primary standards:These standards for the air pollution control considered the public health…

Q: Describe seepage velocity.

A: Seepage velocity seems to be the groundwater velocity determined according to the Darcy rule.…

Q: How many studs are require for the exterior wall on the main floor if there are two doors and 6…

A: Hi! Thank you for the question As per the honor code, We’ll answer the second and third question…

Q: D#2: Write different uses of Surveying?

A:

Q: Road survey including plan , L section & X-section

A: Road Survey : Road survey is the process to know the properties of the site to where new highway is…

Q: What is the arch dam?

A: Arch dam: It is a curved concrete dam, convex upstream and resists force acting upon it mainly by…

Q: Discuss MINIMUM COVER REQUIREMENTS AND STANDARD DIMENSIONS

A: Throughout reinforced concrete, the concrete cover is indeed the shortest route between the layer of…

Q: Describe how you would ensure a fire belt of appropriate width is created around the entire farm…

A: Solution: GIS  refers to the Geographic Information System which analyzes, manage, creates and maps…

Q: ng plan drawing that is related to water resources engine

A: A working sketch or blueprint is one that is based on explanations. It's finished with a detailed…

Q: Define hydrogeology.

A: Hydrogeology:

Q: How to simplify eq 1 , 2 and 3

A:

Q: solve the following exercise: 1- Calculate the original area of the plot (Black border) 2- Calculate…

A: Area is a measure of the size of a two-dimensional surface, typically expressed in square units. It…

Q: Please Help me make a layout plan for the construction site for a housing project.

A: The layout plan includes the details of floor such description and size of bedroom, kitchen, living…

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.