One of the smooth vertical walls supporting end B of the 110-kg uniform shaft is turned through a 35° angle as shown here. End A is supported by the ball-and-socket connection in the horizontal x-y plane. Calculate the magnitudes of the forces P and R exerted on th ball end B of the shaft by the vertical walls C and D, respectively. Assume a = 6.9 m, b = 2.1 m, L = 8.2 m, and 0 = 35°

One of the smooth vertical walls supporting end B of the 110-kg uniform shaft is turned through a 35° angle as shown here. End A is supported by the ball-and-socket connection in the horizontal x-y plane. Calculate the magnitudes of the forces P and R exerted on th ball end B of the shaft by the vertical walls C and D, respectively. Assume a = 6.9 m, b = 2.1 m, L = 8.2 m, and 0 = 35°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The internal shear force Vat a certain section of a steel beam is 94 kips. If the beam has the cross section shown (assume a = 2 in., b1 = 4.4 in., b2= 7 in., tw= t;= 1 in., d = 11.9 in.), determine: (a) the value of Q associated with point H, which is located 2 in. below the top surface of the flanged shape. (b) the maximum horizontal shear stress Tmax in the flanged shape. y a Н tw b2 Answers: (a) Q = i in.3. (b) Tmax i ksi.
6. Z section) s) Calculate the axial stress in the x direction at corner A and corner D. (Point C is the centroid of the cross B= 20° M=10 kip.in 2 in. с 4 in. 3 in. 2 in. 3 in. Axial bending stress at A= Axial bending stress at D = ksi ksi
A pipe with an outside diameter of 4.0 in. and an inside diameter of 3.624 in is subjected to an axial force of P- 850 lb, a horizontal force of P, = 1560 lb, and a concentrated torque of T= 2940 Ib-in. acting in the directions shown. Assume a = 49 in. Section properties for the pipe are A = 2.2514 in. J= 8.199 in.", and I,= 1, = 4.0995 in. betermine the normal and shear stresses at point K, and show these stresses on a stress element T. Answer: Oy = psi Txy psi %3D
Derive the relationship among Unit weight, Porosity and moisture content. - Consider a soil that has a total volume equal to 1. Expressed the weight of soil solids, dry unit weight, moist unit weight - Clue use the formula of porosity to start V₂ V n=
3. In the figure, compute the maximum force P that can be applied, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 3200 psi and 4500 psi, respectively. The diameters are 0.2 inch for the pin, and 0.45 inch for the control rod. Assume double shear for the pin at B. в с 1.5 in 78 degrees T 6 in 2 in
A torque of magnitude T = 1000 N-m is applied at D as shown. Shaft AB and CD have an elliptical cross-section. The major and minor diameters of shaft AB are 56 mm and 50 mm respectively, while the major and minor diameters of shaft CD are 42 mm and 38 mm respectively. Find the maximum shearing stress in shaft CD. Answer must be in MPa
The shaft in the figure has a hollow part from B to A and is solid throughout C to B. The hollow segment is 8mm thick and the shaft has an outer diameter of 80mm. Determine the maximum shear stress developed in the shaft. If B is the midpoint of the 2-meter shaft, and G = 75 Gpa, determine the angle of twist of A with respect to C. PROBLEM 1 B 4 kN-m 2 kN-m
Question: Given: a = 0.4 m b=0.1 m F₁ = 800 kN F₂ = 915 kN M₁ = 400 kNm •A 0.7 m 1 m 1) Find the shear force at Point B, VB: B M, 2) Find the bending moment at Point B, MB:
14-2.5: The stress-strain curve of the axially loaded bar BC is binary and linear, with ϭA=400 MPa, ϭ=500 MPa ,ꜪA=0.004, Ꜫ= 0.016 . Find the total axial displacement at point C. External loads P1=1.6 kN, P2=1.2 kN, cross-sectional area A=10 mm2, bar dimensions a=600 mm, b=300 mm
7-62. Determine the shear-stress variation over the cross section of the thin-walled tube as a function of elevation y and show that Tmax = 2V/A, where A = 2nrt. Hint: Choose a differential area element dA = Rt de. Using dQ = y dA, formulate Q for a circular section from 0 to (7-0) and show that Q = 2R²t cos 0, where cos 0 = VR? - y²/R. ds de `R Prob. 7-62
Six forces are acting on the wedge-shaped block as shown. It is known that F₁ = F₁ F₂ = F₂ = 400 kN, F3 = F₂ = 600 kN, a = 10 m and b = 8 m. The six forces form three couples. Determine the resultant couple. (1). M = 4800kN-m (†) (3). M = 8264kN-m (†) F₁ 30⁰ a (2). M = 4800kN-m (↓) (4). M = 8264kN·m (↓) = 200 KN, F₂
The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 95 lb-ft/ft along its entire length. Using a = 2.0 ft, b = 4.0 ft, and c = 8.5 ft, determine (a) the maximum shear stress in the pipe. (b) the rotation angle oc at the free end of the shaft. b B C Answers: ksi (a) Tmax i rad (b) Pc = i