Answered: of contraction of 0.65 discharges oil…

of contraction of 0.65 discharges oil (SG=0.80) under a head of 8 m. The average actual velocity of the jet is 11.65 m/s. Compute the diameter of the jet at the vena contracta

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Oil flows through a small standard 25 mm diameter orifice under a head of 5.4 m at the rate of…

Q: Calculate the discharge through a 90-mm diameter sharp edged orifice in a closed container with oil…

A: Givend=90mmh=3mP=24kPaC=0.65

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A: Given:The diagram of the problem is given below;The volume flow rate through the larger tube, The…

Q: A form stage centrifugal pump running at 600 rpm is to deliver I m'/s of water against a manometric…

Q: Aa certain hydro-power station has a head of 500m between the upper and lower reservior. A.…

A: The given information in the problem is shown in the following attached image:

Q: A certain hydro-power station has a head of 500m between the upper and lower reservoir . a.…

A: GivenH=500mPart aV2=?Part bQ=60 m3/s d=?Part chL=10%V2'=?d'=?

Q: Q2- A (0.14 m'/s) oil has (density 860 kg/m' & viscosity 0.026 pa.s) is pumping from first tank to…

Q: he figure shows a siphon discharging oil (sp.gr.= 0.90). The siphon is composed of 75 mm pipe…

Q: The two-lobe rotary pump moves 0.145 gal of a coal slurry in each lobe volume Vlobe. Calculate the…

A: Given: The volume in each lobe is Vlobe=0.145 gal. The angular velocity of the rotary pump is n=220…

Q: enturimeter of 0.5 contraction ratio has been fixed in a 100 mm diameter horizontal pipe.The head of…

A: Given:d=100 mmcontraction ratio=0.5No flow pressure head=P1ρg=3 m +10.3 m=13.3 mthroat pressure…

Q: e power required to drive t e pump.

A: Need to find the power required to drive the pump.

Q: Cylinder has a bore area of 339cm² and volume 210 cm/min. Calculate the discharge of a pump delivery…

A: Given Data:- bore area A= 339cm² volume V= 210 cm/min. To find:- Discharge of a pump delivery in…

Q: A centrifugal pump has an impeller of diameter 250 mm whose width at the exit is 50 mm. The flow…

A: We are to find the actual head generate by a pump having radial vanes and a manometric efficiency…

Q: A centrifugal pump has an impeller of diameter 250 mm whose width at the exit is 50 mm. The flow…

A: Given data: Write the expression to calculate the discharge.

Q: 1, contractior 1. Consider a low speed subronic wind tunnel with a area ratio for the no2zle. If the…

Q: The centrifugal pump speed is changed when the impeller size is constant. The initial flow is 200…

Q: A nozzle of diameter 20 mm at one end is used to eject water with a 20 m/s of designed velocity.…

A: Given data: The diameter of the nozzle at converged end is d1 = 20 mm. The designed velocity of…

Q: 8. For the system shown below, calculate (a) the volume flow rate of water from the nozzle and (b)…

Q: radial bladed centrifugal pump running at 1440 rpm is to deliver 30 l/min of water against a head…

Q: A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet…

A: Flow area of the pump is A1=π4D12 The flow rate for the suction is Q=A1v1=π4D12v1⋯⋯⋯(1) Discharge…

Q: 4. A pump draws 20 lit/sec of water from reservoir A to reservoir B as shown. Assuming f = 0.02 for…

Q: 18. A centrifugal pump has, to work against a head of 25 metres at a speed of 850 rpm.. The flow…

A: Given data: Head against which pump is working, Hm=25 m. Speed of the rotor, N=850 rpm. Flow…

Q: Calculate the power supplied to the pump shown if its efficiency is 75%. Water is at 25 degrees…

Q: ter orifice has ntr

Q: A Venturi tube is 6 in. in diameter at the entrance, where the pressure is 10 pig. The throat is 4…

A: Entrance diameter of the venturi tube,(d1)=6 in. Throat diameter of the venturi tube,(d2)=4 in. The…

Q: B1. A crude oil of specific gravity 0.75 is flowing through a pipe of diameter 350 mm and the…

Q: A 75-mm diameter orifice discharges 23.41 L/s of liquid under a head of 2.85 m. The diameter of the…

A: To find : The three orifice coefficients. Given : The diameter of orifice is do=75 mm. The…

Q: A centrifugal pump delivers water at a rate of 0.03 m'/sec to a helght of 18 meters through a pipe…

A: We have given data from the question are, Q=30 L/s=301000 m3/s=0.03 m3/sH=18 m,L=90 m

Q: A 72 mm diameter orifice discharges 0.023 m3/s of liquid under a head of 3 m. The diameter of the…

A: Given data: d=72 mmQ=0.023 m3/sh=3 mdv=64.57 mm Need to determine the coefficient of contraction.

Q: For the system shown below, calculate (a) the volume flow rate of water from the nozzle and (b) the…

A: (a) To find: The volume flow rate of water from the nozzle. Given: The diameter of nozzle is d=50…

Q: The discharge velocity is 49 m/sec and 456 mm water gage. The suction pressure is 81 mm water vacuum…

A: Given Data: The velocity of discharge is, Vd=49 m/s. The pressure head at discharge is, hd=456 mm…

Q: Analyze to select the type of the turbine when its diameter is 600 mm, rotational speed is 600 rpm…

A: Given: The diameter of wheel, D = 600 mm The rotational speed, N = 600 rpm The head of water, H =…

Q: (Enter only the values by referring the unit given. Also upload the hand written answers in the link…

A: Given: The specific gravity of crude oil is s=0.75. The diameter of pipe is d=325 mm. The…

Q: A Borda's mouthpiece 200mm in diameter discharges water a head of 4m. Determine the discharge in…

A: Given data:The diameter of the Borda's mouthpiece is The water head is The velocity coefficient is…

Q: 18. A centrifugal pump has to work against a head of 25 metres at a speed of 850 rpm. The flow…

Q: Taking atmospheric pressure head = 10.3 m of water. A 100 mm diameter horizontal pipe has a…

Q: Q-- Consider the following data relating to performance of a centrifugal pump: speed 1200 rpm, flow…

A: Write the given data. N1=1200 rpmQ1=30 L/sH1=20 mP=5 kWN2=1500 rpm

Question

An orifice 150 mm diameter, having a coefficient of contraction of 0.65 discharges oil (SG=0.80) under a head of 8 m. The average actual velocity of the jet is 11.65 m/s. Compute the diameter of the jet at the vena contracta.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A 75mm diameter orifice discharges 26 L/s of liquid under a constant total producing head of 3m. The diameter of the jet of the vena contracta was measured using a digital caliper and it reads 66.5mm. Calculate the coefficient of velocity.
The pressure drop across a turbine is 25 psi. The flow rate is 55gal/min. Calculate the power output of the turbine.
6.7. Calculate the force exerted by the water on this orifice plate. Assume that water in the jet between orifice plate and vena contracta weighs 4.0 lb. 0.75 0.20 10' d
The discharge velocity is 49 m/sec and 227 mm water gage. The suction pressure is 48 mm water vacuum and velocity of 3 m/s. Calculate the fan total head in terms of water. Answer in cm.
A pump is operated is 3 hp with an efficiency of 65% which is able to deliver water 100 gal/min flow rate water (density 62,4 lb(m)/ft3). Calculate the developed head in ft. Keep 3 sig. figs
A given centrifugal pump works at a flow coefficient Cf=0.65 The pump has a diameter of 3.0 cm and a the out surface 1.3 cm^2 and runs at rotation speed of 800 rpm What is the actual flow rate? give you answer in Liter/min Your Answer: Answer units
Exercise Problem No. 1: An agricultural land install a pump with a 218mm diameter suction pipe and a 200mm diameter discharge pipe. Respectively each pressure reads 1.12 bars and 0.96 bars. The water flow measured 12,500 liters/min.at normal temperature. Calculate the following: 1.Head at the discharge side, m 2. Velocity Head, m 3. Total Head of the pump, m
Q3: Find the diameter of a circular orifice to discharge (0.015m '/ sec) under a head of (2.4m). If the orifice is in a vertical plane and the jet falls (0.25m) in a horizontal distance of (1.3m) from the vena-contracta. Find the head loss through the orifice
3.
B1. A crude oil of specific gravity 0.75 is flowing through a pipe of diameter 275 mm and the frictional head loss of 5 m of crude oil between the two ends of a pipe which are 525 m apart. Calculate the Reynold's Number, discharge of crude oil in the pipe. Take co - efficient of friction as 0.007 and kinematic viscosity as 10 stokes. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of oil in the pipe is (m/s) The Reynold's Number for the flow is Discharge of crude oil through pipe (in m3/s) is
None
A venturimeter is attached to pipe of 80 mm diameter has throat of 40 mm diameter. It is found that pressure in the pipe and at throat is 400 kPa and 130 kPa respectively Find velocity of the flow in the pipe.