na straight circular pipe, e, is given by the expressi

Q: T The temperture e, radius and 82 of a pipe with inner and outer radius are given by and In (r) 02 -…

A:

Q: Find the specific speed of the pump, if the discharge through the pump is 160 liters/sec, speed is…

A: Given values are, discharge Q= 160litres/sec=160×10-3m3s speed N=1000rpm ,head H=27.5 m The specific…

Q: The ratio of theortical discharge to actual discharge through an orifice is coefficient of discharge…

A: Let us discussion coefficient of discharge.

Q: A pump has a brake horsepower of 35 hp with an efficiency of 68%. Neglecting frictional losses,…

A: Given:Brake horsepower, BP=35 hpEfficiency of the pump, η=68%Height of discharge, h=60 m

Q: where do v sub 1 came from? which is 0.95m/s

A:

Q: he flapper C rotates clockwise allowed to flow through the ope -sition tates clockwise it fills the…

A: As the handle A rotate Counter clockwise, the flapper mover upward.As c raised the water starts to…

Q: nd the diameter of the pipe in mm. The discharge of the pipe is  20 lit/sec with the velocity of…

A: Given data: Discharge of the pipe (Q) = 20 lit/s Velocity of the water (v) = 4.75 m/s Need to…

Q: The length of the divergent portion of venturimeter in comparison to the convergent portion is more…

A: The length of the divergent portion of Venturimeter is three to four times in comparison to the…

Q: Question 8 Describe the possible flows through the network of water pipes shown in figure where flow…

A: At each node, we write out the equation that represents the conservation offlow there. We then…

Q: An orifice of diameter 200 mm is fitted at the bottom of a boiler drum of length 6 m and diameter 2…

A:

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 35 lit/sec with the velocity of…

A:

Q: Q3: Each cord can sustain a maximum tension of 500 N, Determine the largest mass (m) of p pipe that…

A:

Q: For oil flow through a pipe, velocity increases O 1, with decrease in area of cross section O 2.…

A: Option : With decrease in area of cross section

Q: An orifice in a vertical plate is located 1.13m below surface of an oil. The area of the orifice is…

A:

Q: A-20 in Oil SG 0.86 51t 0.8 t A-50 in. SG 2.5

A:

Q: A flue from an oil furnace to the chimney is made from 9 pieces of pipe. Afterbeing fitted together,…

A: Solution:

Q: What is the velocity of the pipe center (m/s)? Given that h3=47.1 cm hy =7 cm h =3 cm Water

A: Solution:

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 35 lit/sec with the velocity of…

A:

Q: The pitot tube is used to measure the velocity of flow at the required point in a pipe Select one:…

A: Given Data⇒ Pitot tube

Q: Petrol is drained from a tank X to tank Y via pipeline A-B (see figure Q3). A pump is then used to…

A:

Q: Q3: Each cord can sustain a maximum tension of 500 N, Determine the largest mass (m) of pip that can…

A:

Q: A 250 mm diameter pipes (f = 0.015), 150 m long is connected in series with another 200 mm diameter…

A:

Q: The pitot tube is used to measure the ratre of flow at the required point in a pipe Select one: True…

A: Pitot tube also called as pitot probe is a flow measurement device which is used to measure the…

Q: The throat diameter of a perfect venturi meter is 1.93 inches and is placed horizontally in a pipe…

A:

Q: n the Picture above OBE locm /Bc = 2Scm Ehe Vtelve of nŋ or rotation cl dao rem Convert this vawe to…

A:

Q: 1. A combination Pitot tube is being used to measure maximum velocity for water flow in a pipe. The…

A: Here we will use the general formula for velocity in pitot tube.

Q: main tempen ber he correct r

A: given:d=0.1insurface tension T=0.005lb/ft

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: Part(a).From the given print,we can say that section A-A contains several parts.for example-It…

Q: Inside a pipe with a constant cross section, water flows. Calculate the total number of lost heads…

A:

Q: 2nkL (61-0,) The temperture radius and 02 of a pipe with inner and outer radius are given by and…

A:

Q: Estimate the velocity needed to achieve the intermittent flow of water on a pipe where flow length…

A: Given   Height, h = 74.67 centimeters                  = 0.7467 m

Q: For pipe shown below Determine the relationship between pressure readings at the numbered points

A:

Q: The ratio of actual discharge to theoretical discharge through an orifice is coefficient of…

A: Given,  In the given statement it is asked If the ratio of actual discharge to theoretical discharge…

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: Given: Velocity of smaller end (V1)=4.3m/sVelocity of larger end (V2)=2.1m/sLength of the conical…

Q: A 20 hp pump with a suction from an open reservoir (10 m above the pump) has a flow rate of 125…

A:

Q: The throat diameter of a perfect venturi meter is 1.59 inches and is placed horizontally in a pipe…

A:

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 30 lit/sec with the velocity of…

A: we know that  Discharge= Area*Velocity Q= A*V Given data Q=30lit/sec =22.2kg/sec V=3.25m/s

Q: ngth of the divergent portion of venturimeter in comparison to the conv

A: The answer is False.