n the quadrilateral ABCD, the following angles are measured: Line AB is 500m long. Angle CAB =79°30' Angle DAB=28°30' Angle DBC =31°30' Angle DBA =84°30' Find the distance BC. Find the distance BD. Find the distance CD.

n the quadrilateral ABCD, the following angles are measured: Line AB is 500m long. Angle CAB =79°30' Angle DAB=28°30' Angle DBC =31°30' Angle DBA =84°30' Find the distance BC. Find the distance BD. Find the distance CD.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: solve 9.18 now please

A: Given:- The radius of the circular area (R) = 6 ft The magnitude of the uniformly distributed load…

Q: Q1/ Find the slope of the line : 3x + 4y = 12. x+3= the slope is y=- m=--

A: Given: The equation of line is, 3x+4y=12 The slope of the line is to be determined.

Q: AB and CB are tangents. If y 137.20 mm and ZABC 67.0°, find: a) 21 -y 21 b) x C

A: Step 1

Q: Compute the vertical displacement at joint G. the area of all bars A = 5 in?, and E = 29,000…

A: The virtual work method, also known as the virtual force method or the unit-load method, is a means…

Q: Determine the slope and displacement at point B by the method of virtual works in Q. 1. ?? is…

A: Introduction : slopes and displacement Slope of a Beam: The angle between the deflected beam and the…

Q: The bearing of a line AB in a closed traverse ABCA is 137°30' and its length is 125.8 m. The…

A: Bearing of line AB: 137°30′Length of line AB: 125.8 mX-coordinate of point A: -5 mY-coordinate of…

Q: Consider the line 6x-3y=4. What is the slope of a line parallel to this line? What is the slope of a…

A: Given:- Equation of line is 6x - 3y = 4

Q: A line passes through the point (9,-9) and has a slope of 3. Write an equation in slope-intercept…

A: Slope -intercept equation of line is y =mx +c Line has a slope of -3 then, y =-3 x + c Given that…

Q: am shown, use double integration method to slope at "B" ite steps) 201 EI = Constant EI dy = ±EI

Q: Use conjugate beam method to determine the slope at C. Where El=100,000KN/m^2 1OOKN A AAm C RB

A: In conjugate beam method Slope at any section in real beam is equal to shear force at that section…

Q: IN THE FIGURE, THE WIDTH OF A RIVER BEING OBSERVED IS 63m. ASSUMING THE TRANSIT BEING USED HAS AN…

Q: 50 N 25°

Q: Find the largest and smallest angle changes with their directions at point A, as the unit…

A: total X direction displacement of linesfor aa=+430×10-6 for BB=-260×10-6×cos60=-130×10-6for…

Q: Determine the magnitude of resultant and its direction measured from y axis if F8 = Go0 and O =20?…

A: Given, FA=700 NFB=600 Nθ=20°

Q: Compute the angle 0 in the below figure (in grad), if you know the directions in grads ɑaB=128.5772…

A: To determine: The angle θ (in grad)

Q: +y B A 20.0° 60.0° +x C The three displacement vectors in the drawing have magnitudes of A-4.75 m. B…

A: Step 1: Step 2: Step 3: Step 4:Step 5:Step 6:Step 7:

Q: The declination at a point Q is 3* 15 east. The true bearing of a line QR is S 30* 30' W. The…

A: To find magnetic bearing of line

Q: The bearing of line AB is N 70° W and the azimuth of line AC is 245 °. Then, the internal angle BAC…

A: To find internal angle BAC

Q: The azimuth of a line AB is 347° 12' and the angle BAC measured is 75° 54' counterclockwise. Find…

Q: 90 kN C A В 4 m 8 m

Q: Determine the horizontal displacement at A. Take E =199947.9615 MPa The moment of inertia of each…

A: Horizontal displacement at A

Q: . The projections of a line in VP and HP are 66 mm and 54 mm long respectively. End A is 12 mm in…

A: Given:- VP=66mm HP=54mm End A=12mm mid point of line=36mm in front of VP and 28mm above HP To…

Q: HW: It is required to measure distance from C to point B (cross the river) see the presented figure.…

A: Given:CH = CG = 2m, GH = 2.3m, AE = 2.5m, AD = 2m, ED = 3.34m, CA 35m,Required:Angle C and ADistance…

Q: The side AB of an equilateral field ABC with an area of 692.80 sq.m. has a magnetic bearing of…

Q: FIGURE, THE WIDTH OF A RIVER BEING OBSERVED IS 63m. ASSUMING THE TRANSIT BEING USED HAS AN EXTERNAL…

A: Given Staff intercept at R = s = 0.8. K = 95 , c= 0 Width of river = 63 m

Q: A rectangular section with b = 250 mm and d = 350 mm, if f = 25 MPa and fy = 420 MPa, the depth of…

A: Given data Width of the beam, b= 250 mm Depth of beam, d =350 mm Tensile strain = 0.006 fy = 420…

Q: 6. Determine the magnitude of the resultant R, if P2 = 978, P3 = 780.

A: Magnitude of vector R is given by equation 9 in step 3 as ∣R∣=321.42.Explanation:Step 1: Given and…

Q: 4. Given two vectors both with a magnitude of 1 making a 67 deg angle, use the law of cosines to…

A: Please see the attached image for the solution. The law of cosines is used to compute the unknown…

Q: Derive the correct equation for the critical angle (ϴ1) using Snell’s Law and ϴ2 = 90°. Be sure to…

Q: 1: Determine the slope and the displacement at ponf B for the beam . B 15m

Q: Determine the slope at Cin terms of El for the frame shown. B0KN 21 Im 2m 20KN 30KN 2m 21 A…

A: Generally, the slope is calculated by calculating the distance between two points (rise over run) in…

Q: A field is in the form of a regular pentagon. The direction of the bounding sides were surveyed with…

Q: ☺ Find the distance from the point pCl,1,1) 1. I 77

Q: 3. Find the angle 0 in the interval [0°, 360°) that satisfies the equation 2 sin0 – i cos0 = 1 +…

A: ASKED: To determine the value of angle θ, which satisfies the given equation and in the given…

Q: Q3. A LINE AB 70 MM LONG IS INCLINE AT AN ANGLE OF 30 DEGREE TO HP. ITS END A IS 10 MM ABOVE THE HP…

Q: 9. The magnetic bearing of line AB was observed to be N 20° W, when the declination was 3° W. Point…

A: Given data in question Magnetic bearing of line AB Magnetic Declination Deflection angle To find…

Q: The magnetic azimuth of line PQ is 283* 36'. The declination at point P is 4* 20 west. The true…

Concept explainers

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.

Question

In the quadrilateral ABCD, the following angles are measured: Line AB is 500m long. Angle CAB =79°30' Angle DAB=28°30' Angle DBC =31°30' Angle DBA =84°30' Find the distance BC. Find the distance BD. Find the distance CD.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introducing Given Data

VIEW

Step 2: Calculation of distance BC

VIEW

Step 3: Calculation of distance BD & CD

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the slope and displacement at point B by the method of virtual works in Q. I. El is constant. 40) Ν 300 N/m 3 m Q. I
The force F = (1.8i – 1.7j – 1.9k) N is applied on the rectangular box. A B Find (a) the projection of F along the line that passes through point A = (1.2, 1.5, -1.7) m and point B = (-1.7,-2, 1.9) m, as well as (b) the corresponding perpendicular component on the line that passes through point A and point B.
Find the horizontal displacement and rotation at point A. EA is constant. USE VIRTUAL WORK METHOD. Final answer must be boxed and rounded to nearest 3 decimal places.
Can you please provide the solution on solving the centroid answers are provided. 1. Centroid from the base : 49.78 2. Centroid from the left side: 77.73
1) The measure of the missing angle in the triangle below is. 95 350
DRILL: DETERMINE THE RESULTANT OF TAE FORCES USING a METHOD OF TRIANGLE AND PARALLELOGRAM (dR) OF THE RESULTANT b.) METHOD OF COORDINATE SYSTEM, ALSO FIND the DIRECTION P-8KN Y-AXIS =201KN 20 >X-AXIS 70 O=16KN
X
60 kN | 20 kN 40 kN 30 B 40° Figure P3.65 3.65 Find the x- and y-coordinates of the point where the resultant of the three forces crosses the plate.
What is the horizontal displacement at D to the nearest 0.0001 in? Displacement to the right is positive and to the left in negative. P = 11k EA = 162,000 k BC is built 0.012 in to short. B C N 3' 3' FL a 3' D
3. Determine the horizontal displacement of point C. El is constant. Use Virtual Work Method. 200lbs/ 100 C100ibs/
Determine the slope at point D of the beam shown using Double Integration Method. EI = constant, E = 70 GPa, I = 2340x106mm
SOLVE EACH PROBLEM USING THE FF. METHODS:• VIRTUAL WORK METHOD• CASTIGLIANO THEOREM the 2nd picture is the answer key