Question 1 of 20 %3D An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R, = 20 mm as shown in the figure. The length I of the member is 3 m. 2 2 1. If a G, = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, %3D %3D Calculate the torque acting in the steel shaft. Select the correct response: 16.621 kN.m 22.694 kN.m 9.973 kN.m

Question 1 of 20 %3D An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R, = 20 mm as shown in the figure. The length I of the member is 3 m. 2 2 1. If a G, = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, %3D %3D Calculate the torque acting in the steel shaft. Select the correct response: 16.621 kN.m 22.694 kN.m 9.973 kN.m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Gkuestrons T ØD VP The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads. You are given the column diameter D = 68 mm, the groove radius r = 6 mm, the distance L= 200 mm, the bending load P=5 kN, and the torque T = 600 N.m. The material data are Young's modulus E = 122 GPa Shear Modulus G = 55 GPa Poisson's ratio v= 0.1 and Yield strength oy = 380 MPa. a) Write a numbered list of the calculation steps required to obtain the factor of safety in yielding based on the maximum distortion energy (Von Mises) criterion.
this is about thermal stress
A pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod is made of SAE 4140 steel, compute the elongation due to a temperature change from -20°C to 140°C. TABLE 3-4 Coefficients of thermal expansion, a, for some t nd concrrete
PLEASE ANSWER NUMBER 3.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
I need the answer quickly
Figure 2 shows an assembly made of a steel tube of internal and external diameter of 20 mm and 30 mm respectively, brass and copper bars, each having 25 mm of diameter. The three materials have equal length of 500 mm and are symmetrically rigidly fixed at the upper end while being joined by a horizontal collar (with negligible mass) at their bottom end. An application of a vertical downward load P on the assembly, results in storing a total of 20 J of energy. Brass Copper Steel Collar Figure 2: A system of steel tube, brass and copper bars The moduli of elasticity for steel, brass and copper materials are Es=200 GPa, EB=100 GPa and Ecu=80 GPa, respectively. Calculate: 2.1. The load P if it is applied gradually 2.2. The load P if it is applied suddenly 2.3. The impact load P that falls from a height of 200 mm above the collar.
The L-shaped rigid bar shown is pin connected at C, welded to a rigid bar AB at point B, and rests on a composite bar at D. Rigid bar AB is attached to two identical rubber (G = 150 MPa) pads with the shown dimensions and having a thickness of 30 mm each. Meanwhile, composite bar DE is made of hollow aluminum (with outer diameter do and inner diameter di, E = 70 GPa) surrounding a solid steel rod (diameter = di, E = 200 GPa). Determine the maximum force P that can be applied to the rigid bar at B if the allowable normal stresses in aluminum and steel are 80 MPa and 200 MPa, respectively and the shear stress in rubber is 30 MPa.Use the following values:Parameters s = 135 mm x = 3.8 m y = 5.5 m do = 60 mm di = 35 mm
1. A cold drawn mild steel, AISI 1018CD is used to fabricate the hollow shaft as shown in Figure Q1. Torque of 15 Nm and 30 Nm are exerted at B and C, respectively. The outer diameter of the shaft is D = 20 mm and the inner diameter is d = 15 mm. If the modulus of rigidity for the steel used is given as G = 78 GPa, determine: a) the maximum and minimum shear stresses at sections a-a and b-b. b) the angle of twist at end C. 0.3 m A a; B 15 Nm 0.8 m b. b: Figure Q1 с D 30 Nm
2. Justify the simplification of this problem to only modeling one-eighth of the cross section 3. Construct two-dimensional elements grid (i.e., grid/mesh region), make the correct numbering and labeling of the nodes and elements.
Q/ For the shaft shown in the figure below, find: Maximum torsional stress in part AB, Maximum torsional stress in part BC, Maximum twisting angle in part AB, Maximum twisting angle in part BC, Total twisting angle of the shaft, Thermal elongation of the shaft. Internal force developed in the shaft if it fixed at both ends. Let E = 200 GPa, G= 80 GPa and a = 12 x 10 1/°C. a B. T, T, d, a, b and T are given in the table below. T2 (mm) (N.m) T (N.m) AT b a d (°C) (mm) (mm) 35 300 280 40 420 350
Please Give detailed Solutions and Correct Answers.Solve the problems below : (Use 4 decimal places for all your computations )