M N.M A150 N 300 mm 9o N 400 mm

Q: Calculate the maximum tensile and compressive stresses in the brass and aluminium.

A: A composite beam is formed with more than one material to increase its load resistive strength. When…

Q: Specify a cylindricity tolerance of .0004 for the largest cylindrical surface on the part in the…

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: Bar AB has an angular velocity wAB = 8 rad/s. (Figure 1) AB 200 mm 500 mm e = 45° • PartA Delemine…

A: Solution:

Q: 4)The tooth shape factor Y-. for helical gears should be determined by . В. cos B C. cos, D. cos² ß…

A:

Q: 18 It is given the nodule R=4. nunber of teeth z-25.please calculate the addendua circle (da),…

A: Given: The module, m = 4 The number of teeth, z = 25

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: The shaft is running 30 days at a speed of 48 rps and works for 39.2 hours per day.Find the life of…

A:

Q: Find the following. Show complete solution.

A: The given diagram is here, Section 1:- A rectangle OABC, whose sides are 120 mm and 80 mm Section…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Number of teeth of gears z1: 22 Tooth numbers of gears z2: 90 Tooth numbers of gears z3: 23 Tooth…

A: Here motor is driving the gear 1 shaft which is in mesh with gear 2. Gear 2 and 3 are at same shaft…

Q: =o7 Cm) findSmax. tor Figure 0,7 Cm) fin mox. tor tigure tigure. 225 mm J0omm

A: Given Data The force acting in the downward direction is: F=400 N The height of the weld is: h=0.7…

Q: A power transmission shaft is to carry a steady 30 horsepower while rotating at 1000 rpm. Specify a…

A:

Q: 7. 8. is an important part of proper reservoir operation. filters protect a pump from dirt in a…

A: According to the given data 7.________filters protect a pump from dirt in a reservoir. 8.…

Q: FAND e Canrid 35 300 SECTION MODULUS , Sx, S O radius of giyntion, rx RuF DMEHSIONS '.RE IN MM. I O…

A: As per guidelines one need to solve only first 3 subparts

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: Draw SF and BM diagrams for the shaft below. 2 kN/m B 600 mm 450 mm 300 mm

A:

Q: m. nd Find the components of the equivalent force. Express the re Express the z, y, and z components…

A: The position vectors are-

Q: 181-2,4,0)m A0, 0-6) m Dl0,0, -3 )m w •10 KN ト

A: From the free body diagram given, write the tensions in the cables in cartesian vector form by using…

Q: How long is the thread at 4B?  What do the brackets around dimension 241 at 3C indicate?

A: It is asked to find the length of thread in section 4B and also the meaning of parenthesis in…

Q: 45,00 10,00 30,00 15,00 15,00 018.00 70,00 00'07 10,00 00'0 00'S 00'0

A: Given: Draw ISOMETRIC VIEW

Q: 200 MPa 100 MPa 300 MPa

A:

Q: Problem 4.138 Replace the loading by an equivalent resultant force and couple moment acting at point…

A:

Q: ZPQ'R= = LPQ'R= = MI i O rad

A:

Q: R = 625,000 Pa d,m d. .05 m d. de Find Pi, V. , Vs

A: Given:P2=625000 Pad1=0.1 md2=0.05 m

Q: Solve using characteristics of equations. 5. у" + 14y' + 49у 3D 0%;B у(-4) %3 -1; у'(-4) 3D 5

A:

Q: Please derive the two Diameter Formula for SI Units. See figure. Thank you so much Dear, your work…

A: Solution:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A: It is asked to find the volume of the model based on the given dimensions

Q: Given the shaft with multiple torques on it, calculate the internal torque developed in the BC…

A: To find torque in shaft BC

Q: On the drawing attached, what is the coaxility tolerance that is implied between the two diameters…

A: Given: ∅O=30/30.2∅I=12/12.3To find:Coaxility tolerance

Q: how to get the -y theo

A:

Q: 12 Find maX. W=? if of530Mpa Ś GoMpa い Joomm 2m An 30 そaん 500

A: Stress When body is subjected to any load then body resist that load and the resistance is called as…

Q: Compute for the value of the uniformity coefficient with the data shown below. D10 = 0.08 mm…

A: UNIFORMITY CO-EFFICIENT: It is defined as the ratio of size of opening that will just pass 60% of…

Q: intiguration. 250mm L₂= 164.35 mm O₂ = 86° 44=26mm L₁=173mm WAB-rad/s C 8₁= 90° B KAB=0.80672 rod/s²

A:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. A = 3.55 B…

A:

Q: You want to upgrade the tires on your truck. The manufacturer tires are P160/70R14. You want to…

A:

Q: A WAB 3 m B 2 m 60° D C 1.5 m 45°

A: Given,  WAB= 2 rad/s

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.