A jet of water flows from a 12.5cm2 crater with a constantcharge of 1.125 m where theminimum cross-section level is 1m above ground level. And thatthe extrusion travels ahorizontal distance of 2 mbefore hitting the ground. Calculate the treatment ofdrainage, velocity, andshrinkage. If the drain isthrough the nozzle 3.65

This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

jet of water flows from a 12.5 m2 crater with a constant =harge of 1.125 m where the ninimum cross-section level is n above ground level. And that he extrusion travels a orizontal distance of 2 m pefore hitting the ground . Calculate the treatment of Irainage, velocity, and hrinkage. If the drain is hrough the nozzle 3.65

jet of water flows from a 12.5 m2 crater with a constant =harge of 1.125 m where the ninimum cross-section level is n above ground level. And that he extrusion travels a orizontal distance of 2 m pefore hitting the ground . Calculate the treatment of Irainage, velocity, and hrinkage. If the drain is hrough the nozzle 3.65

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Prob.5. Two parallel plates kept 100 mm apart have laminar flow of oil between them, maximum velocity of 1.5 m/s. Calculate - (i) Discharge per metre width (ii) Shear stress at the plate
A hydraulic turbine works under head (h) and speed (N) is generating a power (Po) using a fluid has density (p) flows through a pipe of diameter (D). If the gravitational acceleration is (g), write an expression of the turbine power?
3.7 m 4 cm 3 diameter Group (D) 7.2 m Determine the discharge, the velocity of flow and pressure at the point (2)?
Answer is 17.4N horizontally and 17.8N vertically.Please show steps in detail.
A 200 mm long downsprue has an area of cross section of 650 mm where the pouring basin meets the downspure. A constant head of molten metal is maintained by the pouring basin. The molten metal flowrate is 6.5 × 10’ mm’/s.Considering the end of the down sprue to be open to atmosphere and acceleration due to gravity as 10' mm/s² at it ends,find the area of thesprue at the end. A,= 650.mm2 %3D 200 mm
Need asap in 25 min i will give like
I need an answer in a very short time
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. a.0.636 b.0.98 c.0.629 d.0.989
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discharge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cc. a.0.629 b.0.98 c.0.989 d.0.636 PLEASE INCLUDE FIGURE OR FBD
b) Oil flows through a 30 mm diam eter pipe Then the pipes 16 uplit into two, wher eby the firot Pipe If 10 mm diameter with 0-3 m/r velo(ity and the other pipe is 15 mm diameter with 0-6 mis velocity Cal culate the flowrate and velo city in 30 mm diameter pipe .
This is Thermodynamics subject. Complete solution with GIVEN pleaseee. Thanks a lot.
As quickly as possible please