It is desired to raise the temperature of a given gas in a container as much as possible with the available heat source. Two paths( at constant pressure and at constant volume) were suggested to choose one to be used. As an engineer give your opinion on the path that will be most suitable in this scenario giving your reasons.

Q: Which one of the following uses high temperature of about 600°F to produce electricity? a.…

A: Temperature: 600 F which sources use this temperature for the production of electricity?

Q: In distillation of kerosene, a steel pipeline (k = 47 W/m.°C) with inside surface temperature of…

A: Given that, The inside surface temperature of steel pipe T1 = 250oC  Inside diameter D1 = 8 cm =…

Q: Choose the correct option: 10. What is the main characteristic of multiple effect evaporators? a)…

A: in multiple effect evaporators 2 or more evaporators are put in series in such a way that steam…

Q: Why the temperature of the gas exiting the CSTR is different from the temperature of the entering…

A: Constant stirred tank reactor (CSTR) is a continuous, perfectly mixed reactor.

Q: 5.3-6. Unsteady-State Conduction in a Brick Wall. A flat brick wall 1.0 ft thick is the lining on…

A: To solve this problem, we can use the following equation for unsteady-state conduction in a…

Q: 1000 lb / hr of oil at 100 ° F flows in a pipe having an ID inch. This oil will rise in temperature…

A: The mass flow rate of oil, moil = 1000 lb/h Initial temperature of oil, Toil,i = 100ºF Inside…

Q: The energy transfer between the hot fluid and cold fluids is brought about by their complete…

A: We have to answer which type of heat exchanger is used where the hold and cold fluid is direct…

Q: Explain how the design and operation of a heat exchanger in a non-reactive process differs from that…

A: Heat exchangers are critical components in process engineering, facilitating the transfer of heat…

Q: Identity the type of energy transferred to your body in each of the following as either energy,heat…

A: The transfer of energy to body takes place in the form of heat transfer, work done or by changing in…

Q: Liquid food is heated in a tubular heat exchanger.  The inner pipe wall temperature is 110 ° C.  The…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: 1.3-4. Heat Loss from Steam Pipeline. A steel pipeline, 2-in. schedule 40 pipe, contains saturated…

A:

Q: The compression ratio of an air-standard dual cycle is 12, and the pressure at the beginning of…

A:

Q: 6.3 In a particular application involving airflow over a sur- face, the boundary layer temperature…

A: All answers are attached below; please check. Explanation:Step 1:Step 2:Step 3:Step 4:Please rate my…

Q: 2. Circular (or annular) fins are employed around the cylinder of a lawn mower engine to dissipate…

A:

Q: In a desert chemical plant, the operator wishes to store chilled water underground in a spherical…

A:

Q: Use the on-line psychrometric chart (link in this module) to help solve this problem. The surface…

A: Given data: Surface temperature of the steel duct = 18 0C Dry bulb temperature of the surrounding…

Q: 19.4 The fuel plates in a nuclear reactor are 4 ft long and stacked with a 1/2-in gap between them.…

A:

Q: 5. . . ) In a manufacturing process, a long, coated plastic rod (p = 2200 kg/m³, c = 800 J/kg K, k…

A: The time it take to the surface of the rod to reach 175o C, the temperature above which the special…

Q: is flowing at a rate of 15 kg/s. For this type of flow, the Nusselt number is given by the following…

A: Given data: Mass flow rate of fluid = 15 kg/s Density of the fluid = 881 kg/m3 Viscosity =…

Q: The temperature on one side of a 6-in. thick solid wall is 200°F and the temperature on the other…

A: Given that, Thickness of the solid wall x = 6 in × 1 ft12 in = 0.5 ft Temperature on one side of the…

Q: Q.2 An Aluminum plate of area 500cm2 is heated up for 5 seconds and its temperature increases from…

A: Area of Aluminium Plate=500cm2=0.05m2 Thickness=2cm=0.02m Mass of Aluminium plate=3.46kg Time up to…

Q: Q2. An annulus consists of the region between two concentric tubes having diameters of 3 cm and 5…

A:

Q: Q5) A cube of aluminum 10 cm on each side is initially at a temperature of 300 °C and is immersed in…

A:

Q: True or False

A: Ans 1- True  2-  False ( because cooling and chilling rate are governed by any of form it can be…

Q: A hot steam pipe having an inside surface temperature of 250◦C has an inside diameter of 8 cm and a…

A: Given: Surface temperature at the inside of the pipe, T1 = 250°C Inside diameter of the pipe, d1 = 8…

Q: The walls of the refrigerated storage room are 10 m long and 3 m high and constructed with 100 mm…

A: Given data: Thickness of concrete blocks = 100 mm Thermal conductivity of concrete blocks = 0.935…

Q: Q2/ Air at atmospheric pressure and 27 °C is blown across a long 4.0 cm diameter tube at a velocity…

A:

Q: A 4 mm diameter tube, 40 cm long, closed at one end and standing vertically on its closed end, is…

A: Given, d= 4mm, L=40 cm, T=17oC, ρ=790 Kg/m3 System is uni-component diffusion…

Q: A furnace is required to sinter powder-metal parts. It operates continuously at 650 °C while the…

A: