A simply supported wood beam carries a concentrated load of P- 12800 Ibs as shown. The beam spans are L-7 ft and L2 - 14 ft. Therectangular cross section has a width of b - 7.0 in. and a depth of d - 17 in. At section a-a, which is x, - 3 ft to the right of pin support A.determine the magnitude of the horizontal shear stress in the wood beam at point K, which is located yk - 5.5 in. below the centroidal zaxis.LAnswer:TKpsiSave for LaterAttempts: 0 of 1 usedSubmit Answer

Answered: Image /qna-images/answer/5b77f75d-6e68-4996-9259-ef118a0a7f5d.jpg

Answered: in. At section a-d, cermine the…

in. At section a-d, cermine the magnitude of the horizontal shear stress in the wood beam at point K, whic gular cross sectic and a depth a Yu swer: psi ave for Later

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 2-FIlexure Formula A beam with an S380 x 74 section carries a total uniformly distributed load of 3W and a concentrated load W. Determine W if the flexural stress is limited to 120 MPa. S(section modulus) = L = 1060 x 10° MPa %3D 5W W B - 1mk 1mf By 3m Value of reaction By Moment(maximum) in terms of W %3D Value of intensity, W Solution: II
Problem 6.142 The reinforced concrete beam is made using two steel reinforcing rods. Figure 1 4 in. M of 1 8 in. 6 in. 8 in. 18 in. 2 in. 1-in. diameter rods. Part A If the allowable tensile stress for the steel is (Ost) allow = 36 ksi and the allowable compressive stress for the concrete is (conc) allow = 3.1 ksi, determine the maximum moment M that can be applied to the section. Assume the concrete cannot support a tensile stress. Est = 29 (10³) ksi, Econe = 3.8 (10³) ksi. (Figure 1) M = Submit ΠΑΠ ΑΣΦ ↓↑ vec My Answers Give Up ? Provide Feedback kip.ft Continue
The assembly consists of two posts AD and CF made of A-36 Steel (E= 200GPa) and having a cross-sectional area of 1000m^2 and a 2014-T6 aluminum (E=73.1GPa) post BE having a cross-sectional area of 1,500m^2. If a central load of 400KN is applied to the rigid cap, determine the normal stress in each post. There is a small gap of 0.10mm between the post BE and the rigid member ABC.
The prestress T-beam section has a simple span of 6 m. The tendons is subjected to an initial stress of 900 MPa with an area of 800 mm?. Assuming a loss of stress of 18%, no tension will be acting at the bottom and a maximum stress of 9.5 MPa at the top should not еxceeded. -450- 100 800 |100 150- Determine the stress at the top due to the final prestressing force alone. (MPa)
Determine maximum shear stress
H.W No.1: The concrete I-beam of figure is pretensioned with four bounded stranded cables having total area (371 mm²). Eccentricity of the steel varies parabolically from 0 at the support to 193 mm at the center of 9 m span. The effective stress in steel after losses is 910 MPa. 254 mm 102 mm 76 mm 102 mm 193 mm 9 m a-what superimposed load will produce a balanced condition of external equivalent prestress load, such that uniform axial compression will be obtained in the concrete. b-what superimposed uniform distributed load will produce cracking of the beam, given the modulus of rupture f=3.28 MPa. c-compute the flexural strength of the beam and compare with the cracking moment. Use: fe = 27.6 MPa, fpy= 1469 MPa, fpu= 1724 MPa. Aps fps a= 0.85 feb --) M₁ = Aps fps (dp- Mn Mn = Pp fps bdp² (1 -0.59 x P x Ips) fci Apf = 0.85 f (b-bw)h fps Apw = 0.85 bw a fps a= Apwfps 0.85 fobw
The uniform 3000kg bar is supported by a smooth wall at A and by a pin at B. Determine (a)the diameter of the smallest pin that can be used if not to exceed a shear stress of 60MPa(Drawthe required FBD and answer in mm)(b) the bearing stress in thesupport bracket (Draw the required FBD and answer in MPa)(c) the bearing stress in the bar at B (Draw the required FBD and answer in MPa).
PROBLEM 2 Strips A and B are to be glued together using the two strips C and D. a. Determine the required thickness t of C and D so that all strips will fail simultaneously. The width of strips A and B is 1.75 times that of strips C and D. b. Compute the axial stress in strips A and B if the width of C and D is 300mm. c. Compute the shearing stress if the gap between A and B at the center is to be neglected and the length of D is 500mm and the width is the width computed in (a). 30 mn 30 mm 40 N 40 N
E6
suppo W given that the top edge of the pipe must have zero stress at the section where the [8,022; 41,23 k
Check the adequacy of the isolated T-beam shown below according to ACI Code requirements and determine the design flexural strength (Moment) for it, use: • f = 20 MPa. • fy = 420 MPa. Effective depth d = 610 mm. • Reinforcement is 6Ø25mm (ABar = 490 mm?). 500 mm 125 mm 700 mm 6Ø25mm 250 mm
Q. At a forint in' a structural member, trianial stresses домра experienced as follows. (A) are чомра. (a) Determine the magnitude of prinicipal stresses and man. shear stress (b) Determine the location of principal plane & flane of 80mla (c) Draw all the stresses by complete, sketch. loumpa. man shear Icompa помра