In a 5.00m x 7.00m room, compute the number of tiles necessary to cover the floor if the tiles to be used is 30cm x 30cm unglazed ceramic tiles. Use 6% breakage allowance. Size of door is 0.70m x 2.00m.

In a 5.00m x 7.00m room, compute the number of tiles necessary to cover the floor if the tiles to be used is 30cm x 30cm unglazed ceramic tiles. Use 6% breakage allowance. Size of door is 0.70m x 2.00m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Estimate the tile work, ceiling and paint of a two storey residential building with the 14.3m x 8.5m…

Q: 40. Determine the rebar that needs to be ordered to construct the wall shown in Figures 5-26 and…

A: Consider the footing plan as in Figure (1).

Q: What are the merits of using glazed hollow clay tiles for partition construction?

A: Answer Hollow clay tiles glazed used only one or both sides for the construction purpose.

Q: 11. Show the Elevation and Sectional View of walls made in English, Flemish, Stretcher, Header and…

A: 11. Elevation view and Sectional view of different walls are shown below: 1. English bond:…

Q: e provided in a wall? b) Why? c) How may they be constructed

A: a.) Weep holes are provided in masonry walls, retaining walls, underpasses, wing walls and other…

Q: 01/ The given data of a rectangular tank are: The bottom is hinged and top is free, a-4 m, b-12 m,…

A: The minimum wall thickness for flexural requirement: Thickness of tank is adopted based on the…

Q: Why is plenum rated cabling required above ceiling tiles?

A: A plenum, which is often located between a drop-down ceiling and the structural ceiling in…

Q: You are designing a fire wall between a small tool rental center and a spray paint shop. Assuming…

A: In order to ensure fire safety, imagine you are assigned the task of designing a firewall between a…

Q: 1149 2.024 19.824² 26 04kN/m 1512kN/m -3.985m с 28.72KN 8-38 kN/m 26.04 kN/m be bi

A: 1) Reaction : ∑Fy = 0 RA + RB + RC + RD = ( 15.2 X 5) + ( 8.38 X 3.885 ) + ( 0.5 X 2X…

Q: 3200 HW No. 1 From Given plan and section below, Estimate Quantity of (Footing, Block wall under…

A: S. No. Details of work No Measurement Quantity Unit Length mm Breadth mm Height mm 1 Earth work…

Q: Problem No. 2 Find the number of 150mm thick, 200mm x 400mm concrete hollow blocks required for a…

A: NOTE : as per our guidelines we are supposed to answer only first question. Kindly repost the…

Q: A 10-foot high by 75-foot long wall will be faced with standard size brick 3 1/2 x 2 1/4 x 8…

A: Wall is a structural member which has many uses such as It act as a partition for rooms It act as a…

Q: Design the reinforced concrete wall shown if fe= 4000psi and fy = 60,000 psi (use ACI -318 code) Vu-…

A: Height of wall, H=hw=12 ft=144 in Length of wall, L=lw=12 ft= 144 in Concrete strength, f'c=4000…

Q: 12. In a one-way slab 50% of the #8 tension epoxy coated bars are going to be spliced. At the…

A: Given Data: The diameter of main bars is db= 1 in. (Imperial Bar size of #8) The rebars are epoxy…

Q: Compute the area of the wall. * QUANTITY Cement 68 bags CHB 6 inches Rough plaster (2 sides) 21mm…

A: Given data, Bags of cement = 68 Plaster thickness both side = 21 mm (Single side = 10.5 mm = 0.0105…

Q: Identify which of the four types of shown masonry blocks shown below might be used for: A fire rated…

A: Split-face brickwork is a desirable material in commercial construction projects because it is…

Q: A retaining wall with a brick face is 70 feet long and 12 feet high. The size of running bond bricks…

A: 2.5 in x 3.75 in x 8 in brick size3/8 in mortar

Q: Briefly describe the following i. Dressing of stone ii. Importance of 'frog' in clay bricks iii.…

A: (i) Dressing of stone: The process to convert the quarried stone into the required and useful shape…

Q: 1. Determine the number of 7 5/8-inch-high by 5 5/8-inch-wide by 15 5/8-inch-long concrete blocks…

A: Wall is an basic structural member of building/structure.It helps in bearing load and its transfer…

Q: What can be done to reduce moisture penetration through masonry walls?

A: To reduce moisture penetration through masonry walls: Moisture penetration is controlled by…

Q: 14.7 At the base of this CMU wall there are a series of wall cleanouts. What are they for and when…

A: The wall cleanouts are used in drainage piping where a cleanout is required concealed in walls.

Q: What are the circumstances that warrant the installation of plenum-rated cabling above ceiling…

Q: 1. Using the Right-Side Elevation, determine the quantity of brick required to place the brick…

A: To determine the quantity of brick required for a brick veneer face, you need to know the area of…

Q: 2.5 A masonry wall, bearing the load from the upper floors, is shown in the following figure. The…

A: Effective height of wall, Allowable height to thickness ratio, Thickness of wall, To find: The…

Q: 1/ For the plan and section of the wall shown below. Calculate quantities for each of the following…

Q: g) How many cubic meters of crushed sand is required for mortar? h) How many cubic meters of fine…

Q: Volume of brick Estimate the number of bricks (in pieces) and mortar (in cubic feet) needed to build…

A: The question is related to construction engineering.

Q: Masonry brickwork has a density of 148 lb/ft3. Determine the maximum height(FT) of a brick wall if…

Q: State the standard brick size adopted by the Common Brick Manufacturers Association.

A: Answer Brick size has Different Categories 1) Modular 2) Standard 3) Jumbo modular 4) Jumbo Standard…

Q: Determine the design shear strength per meter of wall

Q: What is the total thickness of a wall having 3/8 inch first siding, 2/8 inch rough siding, 3 3/4…

A: Thickness of first siding, Thickness of rough siding, Thickness of studs, Thickness of lath,

Q: What are the major recommendations by manufacturers of clay tiles for low-slope installations.

A: the right slope clay tiles work well on roofs with slopes greater than 20 degrees. the more the…

Q: Determine the surface area of the concrete seawall, excluding its bottom.

A: Structure can be divided into different shapes Arc at top, bottom and back Trapezium at sides

Q: From Given plan and section below , Estimate Quantity of (Footing, Block wall under DPC, Block wall…

A: The dimensions are given, Calculating the volume/quantity of the different items: S.No. Details…

Q: Clean-outs in the bottom of a grouted CMU wall are always required: in all load bearing walls in the…

A: answer:- in the portion of wall with vertical steel EXPLANATION :- Clean out in bottom of the…

Q: Q3: Make a comparison between the types of brick walls shown in the pictures. A В C

A: The pictures shown in the question are types of bonds used in the construction of brick wall…

Q: 7. How to determine the static calculation plan of the masonry house? A. Directly check the table…

A: Masonry constructions consist of laying individual units, which are made of brick, stone and…

Q: Estimate the depth of a one way Solid Slab.

A: Brief concept- The depth of the one-way solid slab is calculated according to the provisions of the…

Q: Exppain the process of covering of concrete placed on the exposed top of an external wall ?

A: Solution: Coping is the process of covering the concrete that is being placed on the top of an…

Q: retaining wall with measurements A 30m x 12m x 6m was constructed with bricks of dimensions 8cm ×…

Question

In a 5.00m x 7.00m room, compute the
number of tiles necessary to cover the floor
if the tiles to be used is 30cm x 30cm
unglazed ceramic tiles. Use 6% breakage
allowance. Size of door is 0.70m x 2.00m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Identify which of the four types of shown masonry blocks shown below might be used for: A masonry wall with heavy vertical reinforcing. Bund beam CMU Split faced CMU Bond beam CMU Open-faced CMU Split-faced CMU Hollow clay tile block Open-end CMU Hollow clay tile block
14.2 Identify the type of bond patterns in the following 2 masonry walls. WALL 1 WALL 2
What substrate should be used under brick floors that will be subject to heavy use?
Design two slab system marked by red Color, live loal 3 KN /m? ,8tile =23 KN/m3, %3D known that Ymortar - 22 KN/m3, 8 plaster = 18 KNims,htile =4omm h mortar - 60 mm fc=28Mpa, fy=414 n Plaster = 20mm, 5m 5m 4m
While inspecting the roof sheathing, you see a continuous void parallel to the crest. Which of the following statements accurately describes the function of this space? A. Resistance to wind B. Ventilation D. Diversion of water
10. A 150mm CHB masonry wall with 20mm-plaster on both faces has a general dimension of 3.6 high by 6m long. Determine the quantity of CHB, cement, and sand needed to construct the wall using Class "D" mixture by Area Method.
Describe the core barrels as single wall or double wall.
10) Commonly used types of steel fire proofing include? a) Spray-applied b) Encasement in concrete c) Enclosed in multiple layers of Drywall d) All of the Above 11) Deflection track is used to? a) Bend metal studs b) Isolates the partition from deflection preventing structural loads from distorting the partition c) Keeping masonry from uncontrolled cracking d) All of the Above 12) Which is not a type of steel frame buildings? a) Moment-Resisting b) Shear c) Braced d) Post-Tensioned
The R value of a substance gives the resistance of that substance to heatflow. The larger the R value, the more resistant the substance is to heat flowand heat loss. The total resistance of this wall is 17.85. The sum of the Rvalues shown is 17.06. What is the missing R value?
Module 5 Base on the given plan below. Estimate the materials needed for external masonry works only. Assume wall height to be 3.0 m openings at: a. common area Doors (0.9x2.1), windows (1.2x1.2) b. t&b windows (0.6x0.6) c. Vertical reinforcement at 80cm O.C. d. Horizontal reinforcement at every 3 layers. e. Use Class B mortar and Class B mixture for plastering. f. Assume 12mm thick of mortar per layer g. 12mm thick for plastering
Complete the table please
4. Explain the hydraulic polished wall and rough wall with the formulas for the pipes.