If the specific speed of a pump is Ns = 418.0 (metric units) and it operates with a rotation speed of 40.0rpm, which volumetric flow rate Q can the pump deliver at a pump head of 20.0m? Assume that the water density is 1000 kg/m and the gravitational acceleration is 9.81 m/s?. L/s

If the specific speed of a pump is Ns = 418.0 (metric units) and it operates with a rotation speed of 40.0rpm, which volumetric flow rate Q can the pump deliver at a pump head of 20.0m? Assume that the water density is 1000 kg/m and the gravitational acceleration is 9.81 m/s?. L/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a stream line steady flow, two points A and B on a stream line are 1 m apart and the flow velocity varies uniformly from 2 m/s to 5 m/s. What is the acceleration of fluid at B? 1. 3 m/s² 2. 6 m/s² 3. 9m/s² 4. 15 m/s²
A water reservoir of 300 (Height) x 300 (width) x 500 (depth) m has its free surface at 250 m above a bottom outlet orifice of 500 mm in diameter. The velocity coefficient of the orifice is 0.96 and the coefficient of contraction of the flow through the orifice is 0.6. Assume that the reservoir has a cubic shape. Q1. Calculate the velcoity of water in the reservoir when it starts to empty (m/s)
Question 1 A hydraulic pump increases the pressure in a system from 500 kPa to 3 MPa at a flow rate of 2 e/s. The fluid density is 820 kg/m³. A shock loss over the pump is 0, 8 m, assume the inlet and outlet of the pump at the same level and have the same diameter. Determine the mechanical power required to drive a pump with a mechanical efficiency of 80%.
A semi-infinite body is constructed from a uniform flow with velocity Vo = 13.1 m/s and a source with strengthA = 1148 at the origin. Determine the stagnation point on the body (rstag-TT) and compute the velocity components Vr and Ve and the velocity components Vy and Vy on the surface of the body at 0 = 1.9 rad. Give your answers to 3 decimal places. Istag m Vr = Ve = Vx = Vy =[ m/s m/s |m/s m/s
The pressure in the outlet pipe from the reservoir is 61.3 kPa abs and h =15 m. Because of the rounded entrance to the pipe, the flow is assumed to be irrotational. Under these conditions, what is the velocity at A (Figure below)? Water h V A O VA = 17.16 m/s VA = 13.1 m/s O VA = 19.35 m/s All other answers are wrong
Problem 4. A vertical 10-cm-diameter water (p = 998 Kg/m³) jet with a velocity of 20.0 m/s at A strikes a circular vane as shown below. The stream leaves the vane in a symmetrical manner at the same elevation as A. Assuming ideal flow, what would be the vane weight if the fluid force imparted by the jet equals the vane weight? (Ans: 47.0 kN) 10 cm 120°
3) An incompressible flow velocity field is given as 1 1 [m/s] r r where r is in meters. (a) Calculate the mass flow rate through the cylindrical surface at r =1 m from z = 0 to z =1 m as shown in Figure A (b) Show that mass is conserved in the annular control volume from r = 1 m to r = 2 m and z = 0 to z = 1 m as shown Figure B a 2 m. I m 1 m 1 m 1 m
A horizontal pipe 1.0 m in diameter and 2.50 km long takes off from a reservoir 100 meters below the reservoir water surface and extends to a valve that is to be closed in 25 seconds. During closure, the flow velocity is reduced from 8 m/s to 0 m/s. Express the required thickness of the pipe in term of X. X is the distance of any section/point along the pipe from the reservoir. Use 1.24 X 105 KPa as the working stress of steel. Assume Up = 950 m/s.
i need the answer quickly
1:09 + O VE" ain IQ Q.JPG > Q1: A pipeline joining a lake and a reservoir whose water levels differ by 91.4 m has a diameter of 45.7 cm and a length of 6100 m and the friction factor f is 0.008. The gravity flow is inadequate and it's necessary to install a pump halfway along the pipeline to act as a booster. The pump equation is H = 183 – 760 Q? + 32.5 Q where H is the head developed by the pump in meter and Q the flow in m'/s .Estimate c) The percentage increase in the flow rate due to the pump. d) The daily operating cost of the pump, if the overall efficiency hour (kWh). 70%, and the cost of power is 0.02 $ per kilowatt- Q2: Tests on a single centrifugal pump running at 600 rev/min gave the results indicated below Calculate: 1- The speed of the pump and input power will be required to deliver 2.72 m of water per minute continuously against a head (including friction) of 15.2 m. 2- The number of pump connected in series to rise the water to 42 m. 3- The number of pump connected in…
Q3) SAE 10W oil at 20°C flows through a straight horizontal pipe. The pressure gradient is a constant 400 Pa/m. (a) What is the appropriate pipe diameter D in cm if the Reynolds number Rep of the flow is to be exactly 1000? (b) For case a, what is the flow rate Q in m?/h? For SAE 10W oil, p= 870 kg/m² and µ = 0.104 kg/(m-s).
A 150 mm diameter pipe 60 m long connects two reservoirs. Determine the difference in elevation between the water surfaces of the two reservoirs if the discharge is 30 liters per second. Use Kc=0.5, K=1 and f=0.02. Select one: O a. 16.0 m O b. 18.0 m O c. 13.0 m O d. 12.0 m