If P 4 kN, determine the stress in the inner spring and the displacem of the plate. The inner spring is 8 mm shorter than the outer spring. Outer spring: n= 40 d-15 mm

Q: 11. Two cutting tools with tool life equations given below are being compared: Tool 1: VTº-1-150…

A:

Q: Design a five-liter car engine that operates on a four-stroke cycle. Decide what the design speed…

A: To design - a five-liter car engine that operates on a four-stroke cycle To determine -    number of…

Q: 50. The movement of the cutter of the shaping machine over the work is called Select one: a.COURSE…

A: Course is a term associated with feed. Crank is a rotating link of the shaper mechanism.  Travel is…

Q: A four stroke eight cylinders square gasoline engine operating at 3000 rpm has a bore equal to 86…

A: Given data  N=3000 rpm d=86 mm ηm=82% ηv=83% T1=300 K  P1=100 KPa   Pimp=1500 KPa K = no. of…

Q: 4. Without using any software, write a G-code programme to produce the part shown in Figure 2. Take…

A: N0 G90 F0.5 S1200 T0101 M03N10 G00 X35 Z2N30 G71 U0.5 R1N35 G71 P36 Q90 U0.05 W0.05N36 G01 X20 Z0N50…

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Water Wheel Design You have been asked to design a water wheel that will generate electricity from a…

A: Given : To find : Mathematical model

Q: 15. The length of the storage aisle in an AS/RS = 240 ft and its height = 60 ft. Suppose horizontal…

A: Length of the AS/RS rack structure (L)=240 ft Height of the rack structure (H)=60 ftVelocity of the…

Q: The redesigned brake caliper is manufactured using SLM from Titanium Ti6Al-4V alloy powder. How many…

A:

Q: The redesigned brake caliper is manufactured using SLM from Titanium Ti6Al-4V alloy powder. How many…

A:

Q: 3. Explain about pipeline pigging?

A: Solution:   Pigging in Pipeline is explained below:

Q: llowing question for th

A: Boiler:- A container that is sealed off and uses fuel combustion to create steam from water. The…

Q: Draw the Ts diagram of the whole process

A:

Q: Maximum gas pressure - 3.5 MPa Seat angle – 45° Calculate: (i) diameter of the valve port; (ii)…

A: Given that ;

Q: 1. The torque required to move up a load using a power screw is expressed as WD₂ tan λ + f 2 1-ftanA…

A:

Q: 1. With 25% efficiency, how much work is produced by Q-in of 31076 J? (answer format: 0000 no units)…

A:

Q: What is the flow rate to a cylinder with a 3-in bore and 22-in stroke that fully extends in 8…

A:

Q: An ammonia compressor has a volumetric efficiency of 85%, operating condensing & evaporating…

A:

Q: 22.33 In Table 22.1, the last tw o properties listed can be

A: The general characteristics of tool materials is given.

Q: What are some of the main materials challenges in running jet engines at high temperatures? Select…

A: Given data:-Jet engines:-Jet engines propel aircraft by expelling high-speed exhaust gases. Air is…

Q: Can someone identify this icon's description in Fusion 360?

A: Solution: Given Data:   To Find: Identify the description of each of the given icon in Fusion 360.…

Q: A four-stroke, 8 cylinder Diesel engine has a cylinder diameter of 10.8 inches and operates at 12.8…

A:

Q: Produce a long slots on flat surface of work piece by: (O Milling process. (O planning process. O…

A: Milling Process is the machining process that is used to remove the material from the workpiece with…

Q: 63. The process of impression a diamond-shaped or straight-line pattern into the surface is called…

A: Knurling is a manufacturing process, typically conducted on a lathe, whereby a pattern of straight,…

Q: When does the Stress concentrations occur in shafts?

A: A resisting force produced in a body on each unit area to counter the deformation of the body is…

Q: Pls.answer thank you! A dryer has a 17% moisture wet feed and 3% moisture of dried product. Find the…

A:

Q: Tumble flow has been found to accelerate .9 the combustion process and improve engine performance…

A: In combustion chamber there are two types of intake flows  1. Swirl 2. Tumble These both are created…

Q: 8. Explain what is meant by mean effective pressure. A four cylinder, four stroke cycle petrol…

A:

Q: a Buyer at Tesla and just received 18,000 tires from Michelin. The floor has discovered an issue…

A:

Q: 50. The movement of the cutter of the shaping machine over the work is called Select one: a.COURSE…

A: Generally shaping machine has two strokes they are 1. Cutting stroke or forward stroke 2. return…

Q: ood work on the promblem but the process is a bit hard to read, can you express

A: Given data as per question Tensile axial force, F=4500 N Outer diameter of tube, do=25 mm Inside…

Q: 13A) coefficient of friction (H) is O a. normal force + limiting friction O b. normal force limiting…

A:

Q: 1. Find the information about Air-conditioner a) Steady-state requirement: explains the speed +…

A: The dynamic mathematical model for vehicle cabin, integrated with evaporator and air handling unit…

Q: he following data were obtained from a time study performed on a horizontal milling machine: Average…

A: Normal Time (Observed Time X Performance  Rating)/100  Thus,  Normal Time for Worker = (4.62 X…

Q: Q125 Develop a methodology for a project report of a small plating workshop, presenting the tools…

A: Firstly, identify the tools used in the workshop and their respective flow rates. In this case, the…

Q: The process defined by the figure is characterized by: O Machining tolerance class up to IT8 O…

A:

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.