HoW - A flanged Coupling having six bolts placed at a pitch cirdediameter of 180mm Connects tuwo leng ths of selid steel shaftingof the same diameter. The shaft is vequited to trans mit so kw* 240 veul min. Assuming the allowable intensities of shearingstress in the shaft and bolts are 75 MPa and ss MPa vespectielyand the maxinmum torque is \.4 times the mean torque, Find:.O the diameter of the shaft.the diameter of the bolts.

Number of bolts = 6 Pitch circle diameter = 180 mm Power P = 80 kW Speed N = 240 rpm Shear stress…

H.W:- A Flanged coupling having six balts placed ata pitch cirde diameter of i8omm Connects two leng ths of Selid steel shafting of the same diometer. The shaft is vequited to trans mit so kw * 240 veulmin. Assuming the allouable intensities of sheaning stress in the shaft and bolts are 75 MPa and ss MPa vespectively and the maximum torque is 1.4 times the mean torque, Find:. O the diameter of the shaft. the diameter of the boits.

H.W:- A Flanged coupling having six balts placed ata pitch cirde diameter of i8omm Connects two leng ths of Selid steel shafting of the same diometer. The shaft is vequited to trans mit so kw * 240 veulmin. Assuming the allouable intensities of sheaning stress in the shaft and bolts are 75 MPa and ss MPa vespectively and the maximum torque is 1.4 times the mean torque, Find:. O the diameter of the shaft. the diameter of the boits.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

None
i need the answer quickly
1. The endurance limit for rotating shaft, if its ultimate strength Su=1600 Mpa is:
A steel shaft (G = 80 GPa) with an external drive of 30mm must transmit a torque of 2700 N-m. The allowable shear stress in torsion is 120 MPa and the allowable rotation for the member is 0.1 rad / m. Design to the nearest millimeter the internal radius required for the steel drive
i need the answer quickly
pair of 14.5 degree full depth spur gears are used to transmit 20kW between shafts 40 cm apart running at 1440 rp.m and 360 r.p.m respectively. The allowable stress and BHN are 600 MN/m, 160 and 550 MN/mm 140 respectively for the pinion and gear. Find the module, number ot teeth and face width. CheCk tor wear.
#21. a puhip fropeller Ahaft haw a diameter off 0.35 meters. the allowabre wrlking and the allowable angle on twist u 1 deqe acrosi ita, lengthe equal to 15 diameters stress in Ahear ia 50 megaPaseals %3D brwe fow maximum torque the thaft can transmit
Design the rectangular key which is located on the shaft motor if the diameter of it Is ( 48 ) mom and shearing and crushing stresses which applied of it are ( 420 ) Nimm and ( 700 ) N / mm' respectively , when the force applied on the key equal to ( 8 000 ) N ? jo 5:18 /
I need the answer quickly
Compute for the induced compressive stress in kPa, of a steel shafting of 59 mm diameter and 954 m in length that issubjected to an increase of temperature of 88ºC. Use 6.5x10-6/F, E = 30x106 psi.
03: A shaft carrying three loaded pulleys with stepped diameters as shown. The modulus of rigidity for the shaft is (G-28GPA) and the shaft segments have the same lengths 48N.m (AB-BC-CD-30Cm). Determinc the following: GON.m 144N,m 1- Maximum shearing stress in the shaft CD. 2- The angle of twist of the pulley A relative to B.
Q2: A rotating steel shaft shown: camied by bearings A and E. Machined surface. S - 500 MPa, reliability is 90%, r-3 mm. What is the life of the shaft if design factor 3? 100 100 - 300 15 kN 200- A 304 3rB -3r 35 450