H Wi Determine the hoop and longitudinad stresses set up in a thin boiler shell of Circular Cross-Section, 5m long and of 1.3m internal diameterr when the internal pressure reaches a value of 2.4 bur ( 24 k Pa). what will then be it's chauge in diameter. The wall thickness of the boiler is 25 mm. E= 21o GPa.

H Wi Determine the hoop and longitudinad stresses set up in a thin boiler shell of Circular Cross-Section, 5m long and of 1.3m internal diameterr when the internal pressure reaches a value of 2.4 bur ( 24 k Pa). what will then be it's chauge in diameter. The wall thickness of the boiler is 25 mm. E= 21o GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!
Question 24 A 3 m long hollow circular tube made from aluminium with an outside diameter 200 mm and a wall thickness of 10 mm is filled with a polymer matrix. It is subjected to a tensile axial force of 500 kN acting uniformly over the entire cross-sectional area of the filled tube. If the elastic modulus of the aluminium is E₂=75 GPa, and of the matrix is Em 15 GPa, calculate the normal direct tensile stresses acting on the two materials and the extension of the tube. = Which of the following answers is correct? The tensile stress in the aluminium is ten times larger than the tensile stress in the matrix The tensile stress in the aluminium is 45.2 MPa and the extension of the tube is 1.8 mm. The tensile stress in the matrix is 19.1 MPa and the extension of the tube is 3.1 mm. O The tensile stress in the matrix is 40.5 MPa and the extension of the tube is 2.5 mm. AMSUN The tensile stress in the aluminium is 54.7 MPa and the extension of the tube is 0.8 mm.
None
A spherical pressure vessel has an inside diameter of 4.9 m and a wall thickness of 17 mm. The 0.27] that has a yield strength vessel will be constructed from a special steel [E = 224 GPa; v = of 250 MPa. If the internal pressure in the vessel is 1410 kPa, determine (a) the normal stress in the vessel wall. Answer in MPa rounded-off to 1 decimal place.
A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs is applied at the end of a 1.7 in lever arm, causing the pipe to twist. What is the maximum stress in the pipe in psi? 20,766.9 Correct Answer: 124,601
The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
I need the answer as soon as possible
What is the stress in the pipe when there is no internal pressure What is the maximum permissible internal pressure in the pipe if the working tensile stress in the brass is 60MPa
P
I need the answer quickly
Question 7 of 20 2 Pa The nigid bar of weight W= 100 KN, is carried by three rods as shown. The mechanism is arranged such that it is symmetrical. Refer to the table for the properties of each material Steel Bronze Coefficient of linear expansion 11.7x 10 18x 100 Moctulus of Elastioty 200 GPa 83 GPa Area, A 500 mm 900 mm Length L 1.00 m 1.60 m Steel Steel Bronze A. W
Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 25139 N force. - 540 mm A ... 180 mm 180 mm 60 mm → B P 3.