Given this transfer fuction of a low-pass filter. Find the cut frequency (image attached below)

Q: Submit (below) a report with the following: 1. The band stop filter block diagram. 2. Hand…

A: The band stop filter is designed by using the combination of low pass filter and high pass filter.

Q: Suppose that a low pass filter with order 7 has a corner frequency 1100 Hz. What will be the…

A: Given data Order of a low pass filter is N = 7 Corner frequency is fC = 1100 Hz Frequency is f = 3…

Q: A high-pass filter is to be designed for speech signal processing. The cutoff frequency is 3.4kHz…

A:

Q: How & Find the transfer function, Center frequency, and bandwidth in figure. what type of filter?,…

A: For the given circuit the transfer function, centre frequency, bandwidth, type of filter and the…

Q: 1k2 R ww ww Vin O Vo H 1uF C

A: It is given a circuit of high pass filter. We need to determine the value of R such that to make…

Q: Consider a cutoff (corner) frequency of 5 kHz. 2. Choose a type of high pass or low pass filter, and…

A:

Q: As part of a radio receiver, you are asked to design a simple bandpass filter using a series…

A:

Q: b) Determine the transfer function of the following block diagram G&ss Gys

A:

Q: Design a series RLC bandpass filter as shown in the figure with lower cut-off frequency f = 400 Hz…

A: A series RLC circuit has, Lower cutoff frequency (fL)= 400 Hz Bandwidth (B)= 9600 Hz

Q: You need an active lowpass filter that has a cutoff frequency of 500 Hz. If the stopband is defined…

A: Active Lowpass filter- A specialized filter which is used to filter low frequency signal and stop…

Q: Write the transfer function for the RC high-pass filter of Figure 2. First write it in terms of jw…

A: The transfer function of RC high pass filter needs to be obtained and the cut off frequency of the…

Q: Draw a notch filter circuit?

A:

Q: for FIR digital LPF with following specifications . -1dB at 0.08x rad/sample . -38dB at 0.7%…

A: FIR refers to finite pulse response filter the impulse response of the filter is finite at finite…

Q: Design a parallel LC band stop passive filter with fo= 5 KHz, C=1µF, B=1KHZ, A) Draw the circuit and…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Design a second order lowpass filter using Tow-Thomas Biquad with poles at −1,000 ± 8995.03? and DC…

A: We need to design a second-order low pass filter using the Tow-Thomas Biquad with poles at…

Q: Give the other types of high-pass filters. Draw the circuit and frequency  response of each.

A:

Q: Design a 2nd order band reject filter having high cutoff frequency of 100HZ and low cut-off…

A: A band stop filter or notch filter rejects frequencies that lie between upper and lower cut off…

Q: What happens when we add 2 outputs of Bandpass filters together? Assuming the first band pass filter…

A: According to the question,  What happens when we add 2 outputs of Bandpass filters together?…

Q: Derive the equation for the order of Butterworth filter and find the transfer function of…

A: To derive the equation for the order of a Butterworth filter, we start with the general transfer…

Q: In a 6-pole, 50 Hz, single-phase induction motor, the gross power absorbed by the forward and…

A: In this question,   We need to determine the shaft torque?  Shaft torque = power/w

Q: Design a series RLC bandpass filter with cutoff frequencies fc₁ = 1 KHz,fc2= 20 KHz, using a 100…

A: cutoff frequencies for bandpass filter are fc1 =1 kHz fc2 =20 kHz Series RLC circuit elements , R…

Q: 1. For the circuit in the figure below, obtain the transfer function type of filter the circuit…

A:

Q: Q.3) Design a second order sallen-key low uss flter with bandwidth 4 KHz. Xe is 3.978K2 and damping…

A: The answer as given below steps:

Q: 6) Consider the RL high-pass filter shown in Figure 5. Find and expression for the complex transfer…

A:

Q: 4. Consider a prototype Butterworth lowpass filter with the following transfer function: H(s) = %3D…

A:

Q: to ด Jo

A: Bandwidth: This is the range of frequency in which different frequencies of the signal occur.…

Q: A signal with bandwidth 100HZ is over sampled by 40% then the cutoff frequency of the low pass…

A: Given parameters are: B.W=100Hz The above signal is oversampled by 40% above the Nyquist rate.

Q: Design a low pass filter for a cutoff frequency of 15MHZ. Confirm your answer with a simulation and…

A:

Q: i. What order and type of filter is this? Shortly explain. ii. Derive the transfer function, H(f),…

A: Given figure Here R=120 Ω,L=15 mH=15×10-3 H,C=2 μF=2×10-6 F. Vin is the input voltage and Vout is…

Q: What order and type of filter is this? Shot ly explain. Derive the transfer function, H(f), for R =…

A: Given figure Here R=120 Ω,L=15 mH=15×10-3 H,C=2 μF=2×10-6 F. Vin is the input voltage and Vout is…

Q: 1. For the circuit in the figure below, obtain the transfer function output voltage / input voltage.…

A:

Q: Draw the circuit of a low pass RL filter and find the transfer function. Cut with a frequency of 70…

A: Given Data:An RL low pass filter having,Cut-off frequency To Find:Circuit and transfer function of…

Q: 2. Hand calculation for different filter's components 3. Detailed list of components and their…

A:

Q: A passive RL filter circult is given below. ll + Vin out a. Determine an expression for the voltage…

A:

Q: 8. Plot the pole-zero patterns of the low-pass, high-pass, band-pass, and band-stop filters.

A: LPF =  LOW PASS FILTER which will Allo the frequency components of a signal which is having the…