Gas and Themal Combined cyde power plant generates total power output equal to 212 MW and 208 MW respectively With their average power, what is the combined effidency if both received power input of 282 MW? 67.82% B) 69.45% 70.45% D. 74.47%

Gas and Themal Combined cyde power plant generates total power output equal to 212 MW and 208 MW respectively With their average power, what is the combined effidency if both received power input of 282 MW? 67.82% B) 69.45% 70.45% D. 74.47%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer letters D, E, F
In a gasoline engine with a compression ratio of 9, the compression process At the beginning, the pressure of the air is 100 kPa and the temperature is 300 K. Heat made into the cycle If the transfer is 1310 kJ/kg, a) Calculate the highest temperature and pressure of the cycle. b) Find the thermal efficiency of the cycle. c) Find the average effective pressure of the cycle, kPa. Note: Specific heats are constant.
A Rankine cycle is used for a steam power plant. Liquid first enters the turbine at 2.25 MPa and 300C then exits at 0.025 MPa. The pump receives saturated liquid from the condenser before sending it to the boiler at the original pressure.a.) Draw the T-S diagram. b.) Find the dryness at turbine exit,c.) Wp, d.) Qa, e.) Qr, f.) Wt, g.) Wnet (kJ/kg), h.) Efficiency(%),and i.) Steam rate(kg/kWh)
d) The condenser of a thermal power plant is to be cooled by a nearby river at 14.5°C, allowing a temperature gradient of 11.5°C for effective heat transfer, stating your reasons, calculate the minimum condenser pressure in bar.
a) In a Power System, Define the following (i) Hot Reserve (ii) Cold Reserve b) With a neat diagram, explain the working of the Tidal Power Plant
a steam 8.0 MPa and 485 degree Celsius enters the turbine and expand at condenser pressure of 0.006 mpa for cycle and 1kg of steam. determine A.) heat added, B.) Wnet, C.) Thermal Efficiency. And for the engine, Determine the steam flow and the energy output of 40,000 Kw, E.) Wturbine, F.) Energy Chargable, G.) Ideal Heat rate
1
A diesel power plant use fuel with HHV of 45000 kJ/kg. What is the density of fuel at 25 deg. C?
A gas increases in pressure from 2 atm to 6 atm at a constant volume of 1 m3. It then expands at a constant pressure to 3 m3, it then returns to the starting conditions in a transformation that makes a triangle. A) Calculate the work done in the cycle. B) If the cycle deposits 500 kJ to the low temperature reservoir, find the heat taken from the high temperature reservoir and the efficiency of the engine. R=8.314 J/K*mol , 1atm=101325 Pa
Thermofluid 4. I his question requires you to demonstrate your knowledge and understanding of gas turbine engines. A small aircraft is powered by a single-spool turbojet engine with a convergent nozzle. It flies at a velocity Vo = 226 m/s and at an altitude where the ambient pressure is 79,500 Pa. The engine intake supplies air at a total pressure and temperature of 101,846 Pa and 300 K respectively. a) b) Draw a process diagram for this engine showing your stage notation and mechanical linkages; Using engine performance data given in Table Q4, determine the engine thrust and thrust specific fuel consumption, stating any assumptions made. Intake air mass flow rate Compressor pressure ratio Compressor isentropic efficiency Combustion efficiency Fuel Lower Heating Value (LHV) Turbine entry temperature Turbine isentropic efficiency Jet pipe total pressure loss Ycold Cp.cold Rcold 1.4 Gas constants Phot Cphot 52 kg/s Rhot 4 87% 98% 43.1 MJ/kg 1060 K 92% 2% 1,005 J/(kg-K) 287.0 J/(kg-K)…
7.) A Rankine cycle is used for a steam power plant. Liquid first enters the turbine at 2.25 MPa and 300C then exits at 0.025 MPa. The pump receives saturated liquid from the condenser before sending it to the boiler at the original pressure. a.) Draw the T-S diagram. b.) Find the dryness at turbine exit, c.) Wp, d.) Qa, e.) Qr, f.) Wt, g.) Wnet (kJ/kg), h.) Efficiency (%), and i.) Steam rate (kg/kWh) • 100%, 3.12 kJ/kg, 3016.3 kJ/kg, 2346.3 kJ/kg, 522.3 kJ/kg, 35.22%, 4.63 kg/kWh • 95.21%, 2.27 kJ/kg, 2809.6 kJ/kg, 1875.21 kJ/kg, 815.33 kJ/kg, 31.29%, 3.51 kg/kWh • 83.73%, 2.27 kJ/kg, 2742.1 kJ/kg, 1964.48 kJ/kg, 779.89 kJ/kg, 28.36%, 4.63 kg/kWh • 100%, 0 kJ/kg, 3016.3 kJ/kg, 271.93 kJ/kg, 2798 kJ/kg, 100%, 1 kg/kWh
A thermal power plant generates 50mw to market and has an efficiency of 54%. Consider that It uses 12% of total energy for its own consumption. Answer: A)How much is the gross power generation of this plant? B)How much is the total intema generation in the combustion chamber to generate 50MW? C)How much would the loss of energy of this plant be?