G a Support reactions will be found in the gerber beam whose loading condition is given in the figure. A is the fixed support, the G point is the intermediate joint, and the B support is the sliding joint. Distributed loads on the beam q1 = 9 kN/m, q2 = 6 kN/m, beam dimensions a = 3 m, b = 2 m. Асcordingly, Gx %3D ? О a) 19.5 ОВ) 45 O C) 0 OD) None. O TO) 6

G a Support reactions will be found in the gerber beam whose loading condition is given in the figure. A is the fixed support, the G point is the intermediate joint, and the B support is the sliding joint. Distributed loads on the beam q1 = 9 kN/m, q2 = 6 kN/m, beam dimensions a = 3 m, b = 2 m. Асcordingly, Gx %3D ? О a) 19.5 ОВ) 45 O C) 0 OD) None. O TO) 6

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

CLO 2: A beam subjected to a uniformly-distributed load has a: fırst-degree shear curve zero-degree shear curve third-degree shear curve second-degree shear curve
17. The simple beam shown supports the concentrated load P = 2000 N. Dimensions a and b are 1.2 m and 1.5 m, respectively. Determine the value of Ely at midspan in N-m³. Rz а. 784 c. 934 b. 806 d. 986
PLS ANSWER ASAP 1. Calculate for the shear at column CB in kN for the frame shown using Portal Method. 2. Calculate for the axial force at beam BF in kN for frame showN using Portal Method. Enter absolute value only. Use a = 23.2 kN, b = 43.3 kN, c = 43.1 kN, Enter absolute value only.ANSWER SHOULD BE IN 3 DECIMAL PLACES
Need help ASAP Determine the max flexural stress in MPa
21. Simply supported beam 8 m length has a 2.000 kg load at the center. The flexural stress is 25,000 kPa. Find the section modulus. A. 6,434.56 in3 B. 1,846.56 in3 C. 79.82 in3 D. 95.78 in3
Problem 2 The lap joint is fastened with four 3/4" diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. ANS: P = 47.3 kips P P 7 in. 8 4 in. 7 81 in. P
9 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, the shear force at point E T=? a) 14B) 2C) 6D) 0E) 4
With FBD
3. A solid steel shaft is loaded as shown in Fig. P-322. Using G = 83 GPa, determine the required diameter of the shaft if the shearing stress is limited to 60 MPa and the angle of rotation at the free end is not to exceed 4 degrees. 750 N-m 1200 N-m 2.5 m 2.5 m-
SFD and BMD by graphical method - distributed load
A Universal beam of I shaped cross-section is 203 mm deep, and 133 mm wide and has a steel plate 150 mm by 10 mm thick fastened to each flange. Ix-x for the universal beam is 28.80×10^6 mm^4. a) Determine the total uniformity distributed load which may be carried over a simply supported span of 6 metres if the permissible bending stress is 165 N/mm^2. Neglect the self-weight of the beam. [Ans.: 124.02 KN/m] b) Determine the minimum central length over which the additional plates are required. [Ans.: 4.23m]
A simply supported beam supports the applied loads as shown. If E = 200 GPa and I = 0.0015 m4. Using double integration method, Determine the maximum delection along span AB only.