For the given beam and loading shown in the figure, (a) determine the support reactions, (b) determine the location of the section with respect to point A where the maximum moment occurs and its magnitude, (c) determine the minimum width b of the cross section for the beam to carry the applied load safely, if the allowable normal stress for the material used in the beam given in the figure is 50 MРа.

For the given beam and loading shown in the figure, (a) determine the support reactions, (b) determine the location of the section with respect to point A where the maximum moment occurs and its magnitude, (c) determine the minimum width b of the cross section for the beam to carry the applied load safely, if the allowable normal stress for the material used in the beam given in the figure is 50 MРа.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLID MECHANICS
Question- Principal stress at a point in an elastic material are 1.50 (tensile), o (tensile) and 0.50 (compressive). The elastic limit in tension is 210 MPa and poisson's ratio=0.3. Find the value of o at the failure when computed by the maximum principal strain theory.
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx= 80 MPa, σy= 35 MPa, and τxy= 84 MPa, acting in the directions shown in the figure. At this point, determine the strain components εx, εy, εz, and γxy. Assume that E = 69 GPa and v = 0.29 for the machine component.
Please solve correctly
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=34 kips is applied to the assembly at A, two loads of Q=25 kips are applied at B, and two loads of R=37 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 32 ksi. The normal stress magnitude in brass rod (3) must be limited to 24 ksi. Determine the minimum diameter (in in rounded to the nearest thousandths) required for rod 2.
Q: A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm2 stress.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume'stress magnitudes of 5,-80 MPa, S - 220 MPa. Sy For the given state of stress at a point in a structural member, determine the center Cand the radius R of Mohr's circle. Answers: C- MPa, R- i MPa. Save for Later Part 3 Determine the principal stresses (api > Op2 ) for this state of stress. Answers: Opl = MPa, o,2 = MPa Save for Later Part 4 For this Mohr's circle, determine the magnitude of the central angle between: (a) pointxand the point representing the principal stress opl- (b) point x and the point representing the principal stress Op2. (a) Angle - i (b) Angle - i
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx= 100 MPa, σy= 65 MPa, and τxy= 70 MPa, acting in the directions shown in the figure. At this point, determine the strain components εx, εy, εz, and γxy. Assume that E = 71 GPa and v = 0.28 for the machine component.
Problem 2 A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa), located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. 2m B 10kN/mm 4m C 2m Steel Aluminum 42 mm 20 mm 13 mun