For the composite given below, taking convection heat transfer effect on both side of the composite, identify which of the following is a WRONG equation3; T Tas Taz KI T2 ba LI T3-Taz h2A Ob. T2-Taz L2 1 K,A h,A Tx1-T2 1 h,A*KA d. T-T2 L2 K,A* K,A

For the composite given below, taking convection heat transfer effect on both side of the composite, identify which of the following is a WRONG equation3; T Tas Taz KI T2 ba LI T3-Taz h2A Ob. T2-Taz L2 1 K,A h,A Tx1-T2 1 h,AKA d. T-T2 L2 K,A K,A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please Write the differential equation which governs the heat transfer
20. The two plates of Problem 11 made of the same material and having constantk are exposed on one side to hot water at Tw and hw and on the other to cold air atTa and ha. Find a) the equation for temperature profile in these plates and b) temperaturesat x = 0 and at x = L if hw = ha = h. [Ans.: a) T1(x) = c1x + c2 where, c1 = hw(Ta – Tw)/c3 and c2 – Ta = – hw(haL +k)(Ta – Tw)/(hac3) where c3 = (k + hwL + hwk/ha)].
B5
A composite wall consisting of five series layers of materials with different properties. Layer thickness, thermal conductivity of the layers and temperatures are shown on the figure. Based on Fourier's law for conduction, answer the following questions. 1. What are the main assumptions? 2. Drive an equation to calculate the heat transfer rate through the Composite wall? 3. Draw the thermal circuit through composite wall? 4. What are the value Ti? 5. What are the value Tj? 6. What are the value Tr? Givens: KA = 2 W/m. °C KB= 1 W/m.°C Kc = 5 W/m. °C Ko= 4 W/m. °C 100°C Ti 25°C Tj Tr A C +2cm + -6 cm 4cm cm
can you please work this out step by step please and do everything
The Golden Gate Bridge in San Francisco has a main span of length 1.28 km, one of the longest in the world. Imagine that a steel wire with this length and a cross-sectional area of 4.10 x 106 m2 is laid in a straight line on the bridge deck with its ends attached to the towers of the bridge. On a summer day the temperature of the wire is 22.0°C. (a) When winter arrives, the towers stay the same distance apart and the bridge deck keeps the same shape as its expansion joints open. When the temperature drops to -10°C, what is the tension in the wire? (Take Young's modulus for steel to be 2.00 x 1011 N/m2, and the average linear expansion coefficient for steel to be 1.1 x 10-Soc-1.) (b) Permanent deformation occurs if the stress in the steel exceeds its elastic limit of 3.00 x 10° N/m2. At what temperature would the wire reach its elastic limit? (c) Explain how your answers to parts (a) and (b) would change if the Golden Gate Bridge were twice as long.
I need the answer quickly
Using Ritz technique, determine the temperature distribution in the fin. T=20 °c, h=0.3 w/cm² °c, k=4 w/cm °c. Assume free end is open to the atmosphere
Question 1 A composite component is comprised of a tube and a concentric rod running inside it, both with a length of 1.5 meters. The tube is made of copper and has inner and outer diameters of 60 mm and 100 mm, respecti vely, a coefficient of thermal expansion and elastic modulus of 17 x10-6C and 117 GPa, respectively. The rod is made of aluminium with a diameter, coefficient of thermal expansion and elastic modulus of 50 mm, 23 x10-6C and 80 GPa, respectively. If the composite is exposed to a temperature rise of 120°C, determine: The sense and magnitude of the stresses induced in the composite if it is not restrained. 1.1 1.2 The sense and magnitude of the stresses induced in the composite ifit is partially restrained with an allowed free expansion of 0.3 mm.
Compute the heat transfer through the composite wall as shown in the Figure below. Consider materials of your choice from table below. Use both methods, thermal conductivity & thermal resistivity.
A wall as given in fig is made up of two layers (A) and (B) The temperatures are as shown in the sketch. The ratio of thermal conductivities of two layers is given as KA = 3 the ratio t, : t, is KB T2 = 1200 T, = 1300° C B T3 = 30 A