For all the computed values with decimals, use four (4) digits after the decimal. Differential leveling runs from BM10 to BM11 at a distance of 7.5 km. It was observed that the leveling rod was inclined 6° from the vertical every time the backsight is taken. The average BS reading is 3.15m and the average length per set-up is 300m. Determine the error every 300m set-up and the correct elevation of BM11 if the recorded elevation was 173.

For all the computed values with decimals, use four (4) digits after the decimal. Differential leveling runs from BM10 to BM11 at a distance of 7.5 km. It was observed that the leveling rod was inclined 6° from the vertical every time the backsight is taken. The average BS reading is 3.15m and the average length per set-up is 300m. Determine the error every 300m set-up and the correct elevation of BM11 if the recorded elevation was 173.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need a solution with clarification. engineering survey Q3) leveling staff setup on a BM of elevation of 89.90 m is observed from point A where the three staff reading are 1.00, 2.37, 3.75 m with a depression angle of 05° 32. Then the staff moved to point B where the three staff reading are(- 0.20, -1.88, -3.57) m with an elevation angle of 04 18. Compute the horizontal distance of B from A and reduced level of stations at B (assume stadia interval factor 100 and the additive constant of the instrument = 30).
While leveling across a river, the staves readings held at (R) and (S) from the instrument stationed at (P) and (Q) : Staff reading at R from P = 1.332m, Staff reading at S from P =1.016m Staff reading at R from Q =1.614m, Staff reading at S from Q =1.278m (R) and (Q) were close to each other on one bank of the river with (S) and (P) similarly situated on the other bank. If the elevation of (S) is (10. 376m) calculate the elevation of (R).
Determine the misclosure and the correction. Express your answers in feet to two decimal places separated by a comma. Misclosure, Correction = [ΫΠ ΑΣΦ ↓↑ vec ? ft
(Alternate Peg Method) In the two-peg test of a dumpy level, the following observations are taken: Rod reading On point A On point B Instrument set-up near M (m) Instrument set-up near P (m) 0.296 1.563 0.910 2.140 Requirements: a. Determine the true difference in elevation between A and B. b. Determine the error in the line of sight for the net distance AB c. If the line of sight is not in adjustment, determine the correct rod reading on A with the instrument still set up near B.
Which of the following may cause errors in leveling measurement? (Multiple choice) (Multiple choice) 1 □ A. The level tripod sinks O B. Reading Error □ C. The instrument is not erected at approximately the same distance from front to back □D. Improper implementation of the centering of the level □ E. Subsidence occurred at the level where the level was erected □ F. Vertical dial error of the level
A reciprocal leveling is observed across a wide river and the reciprocal level readings were taken between points A and B as follows. With instrument set up near A, the rod readings are 3.411m and 3.414 m. The reciprocal level readings on the opposite side of the river at point B arev 4.281, 4.284, 4.283 and 4.285m. With the instrument set up near B the rod readings on the opposite side of the river at point A, the rod readings are 3.153, 3.150, 3.156 and 3.154. a. Compute the difference in elevation between A and B with the instrument setup near A. b. If the elevation A is 100m, what is the elevation at B?
Surveying//Theoritical part.
1. For the given set of data of differential leveling as shown in the tabulation: Station Backsight (m) Foresight (m) IFS (m) Elevation BM1 1.24 837.65 1 2.35 1.76 2.50 4 2.73 3.00 6 2.72 7 1.93 8. 1.05 TP2 2.06 2.78 9 0.68 10 0.98 11 1.29 12 2.45 13 2.67 BM2 2.36 a. Find the difference in elevation of Station 13 and Station 8 b. Find the difference in elevation of Station 11 and Station 4 c. Find the elevation of BM2
When carrying out the permanent adjustments of a dumpy level by two-peg method, the following observation were made. Instrument at E midway between C and D, 100 m apart. Reading at point C = 2.000 m Reading at point D = 3.000 m Instrument at F in line of CD such that CF = 120 m and DF = 20 m. Reading at point C = 1.500 m Reading at point D = 2.750 m Check whether the instrument needs permanent adjustments or not, and whether the line of sight is inclined upwards. What should be the correct reading at C if the instrument is to be adjusted?
Q:The following consecutive readings were taken with a leveling instrument at intervals of 25 m. (3.375, 2.730, 1.615, 4.450, 3.835, 3.070, 2.835, 1.985, 1.435, 2.630, 3.255, and 4.630 m). The instrument was shifted after the fourth and eighth readings. The last reading was taken on a B.M. of RL 111.200 m. Find the RLs of all the points (Height of instrument method).
A horizontal collimation test is performed on an automatic level following the procedures described in Section 4.15.5. With the instrument setup at point 1, the rodreading at A was 3.886 ft, and to B it was 3.907 ft. After moving and leveling the instrument at point 2, the rod reading to A was 4.094 ft and to B was 4.107 ft. What isthe collimation error of the instrument and the corrected reading to A from point 2?
a) In the process of taking a rod reading, one can eliminate parallax mathematically. Parallax is basically a systematic error. True False b) The page check in the field notes is a quality control measure to determine if the user satisfied 1st order class I leveling. True False C) The upper cross hair reading was 8.00 ft. The lower cross hair reading was 6.00 ft. The stadia constant was 100. The horizontal distance from the center of the level to the face of the level rod = 200.0 ft. True False