floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5 kPa and a ormly distributed live load of 1.9 kPa over its surface area. Determine the service (ASD) reaction (kN) of beam chat will be transferred to the girder at G. Girder Floor beam Column 1 H B L IN E H H M 4 at 7.5 m = 30 m D N E 2 at 12 m = 24 m

floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5 kPa and a ormly distributed live load of 1.9 kPa over its surface area. Determine the service (ASD) reaction (kN) of beam chat will be transferred to the girder at G. Girder Floor beam Column 1 H B L IN E H H M 4 at 7.5 m = 30 m D N E 2 at 12 m = 24 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.3.K
H.W Analyze the trusses shown .EA= constant 12 kN 10 kN 10 k 20 k 30 k E ¥B VD 2 m 2 m → 10 k H. 2 m G. 3 m 3 m 3 m
A 3-m-long beam is subjected to a variety of loadings. (a) Replace each loading with an equivalent force-couple system at end A of the beam. (b) Which of the loadings are equivalent?
A steel column carries an axial load of 819 kN and a moment of 63 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 13172 mm2 rx is 109 mm ry = 94 mm Sx = 1200 x 103 mm3 K = 1.0 L= 3.6 m E = 200,000 Mpa Fy = 248 Mpa Use NSCP specification for compressive stress and Fb =148 Mpa. Determine the Compressive Stress if Axial load only existed.
Determine the reactions at A and B for the steel bar and loading shown in figure
L. Mains A beam ABCDE is 5 m/in length and loaded as shown in Figure Q3. Draw the S.F. and B.M. diagrams for the beam, indicating all major values. Find also the value of the maximum bending stress if the beam section is rectangular 30 mm width by 60 mm depth. 3 kN 10 kNm 1 m B 1m 3 kN/m 640044 Stergat 1 m Figure Q2: Beam Loading 2 m SE
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
Calculate the support reaction at roller support A
Please provide solution for this question
The floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5 kPa and a uniformly distributed live load of 1.9 kPa over its surface area. Determine the service (ASD) reaction (kN) of girder AF that will be transferred to the column at F. Girder Floor beam Column E A B H FH- H L G H M 4 at 7.5 m 30 m D N -Io 2 at 12 m = 24 m
A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity g/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. 500 mm L= 20 m 18 mm 1600 mm 500 mm (a) Determine the maximum permissible load q based upon an allowable bending stress oallow = 130 MPa. Round to the nearest tenth. kN Gmax = (b) Determine the maximum permissible load q based upon an allowable shear stresS Tallow = 55 MPa. Round to the nearest tenth. kN Gmax m
Find roller support reaction