Explain the mechanics of frost wedging.
Q: What is the crack pattern induced by hydration due to internal restraint?
A: When the temperature is rising, the inner concrete’s temperature is above outer concrete’s…
Q: Question 17 Arrange in correct order. Tough Wood Steel Glass Brittle.
A:
Q: How can fine pozzolans reduce bleeding of fresh concrete?
A: Bleeding: A phenomena in concrete in which the free water available in the mix rises to the top and…
Q: What is cold bending of steel rebars?
A: This question is related to the Design concrete structure from civil engineering.
Q: choose true or false The No.4 sieve has 4-inch wide openings
A:
Q: The No.4 sieve has 4-inch wide openings a-true b-flase
A: The sieve number denotes the number of holes present in the sieve within one inch length of the…
Q: What is the Liquid requirement rate in perforated plate scrubbers?
A: The liquid requirement rate or Liquid to gas ratio is the volume of liquid injected per volume of…
Q: write short notes on comparison between cement pressure grouting and epoxy grouting.
A: Grouting has been the procedure of inserting content through cavities or fractures in mortar,…
Q: Explain the process of placing roller compacted concrete with a vibratoryscreed.
A: When finishing concrete slabs, Vibratory screed can fit the demands of every job site with a variety…
Q: Why does the amount of air in the concrete decrease as the slump increases?
A: Concrete:- Concrete is a composite material made of fine and coarse aggregate that is bonded by a…
Q: What is the contacting power input in orifice scrubbers?
A: The industries and gas station exerts particulate matter and toxic gases which causes air…
Q: The free water bound water is first removed when wood is dried.
A:
Q: What is the meaning of tablet lamination and capping? How are these related to compression force?
A: Tablet lamination and capping:
Q: Problem: A concrete mix for 3rd level floor, open sided parking garage f'c 30 MPa Slump = 50 -70mm…
A: All tables are taken from ACI 318 1. Find Required Compressive strength : f'cr For f'c = 30 MPa <…
Q: 2) What are lime pops? How are they formed? How do lime pops affect mortar properties?
A: Lime in soil is present in the form of ground limestone rock, which naturally contains calcium…
Q: How to conduct a rebar tensile strength test?
A: Introduction : A sample is typically tugged to its breaking point in a simple tensile test to…
Q: (4) 5  187 #3" fé= 4000 pai Grade 60 steel NWC. Mn=?
A:
Q: how do you find SSD? how is SSD 1.47?how do you determine breaking conditions? How is it 2.5?
A: The speed of the vehicle = 40 mph The gradient of the uphill = 5% To determine:- The value of the…
Q: How can you keep prepared mortar from having excessive moisture loss?
A: Preparation of mortar having excessive moisture loss:
Q: How to Design Sealant Joint.
A: Sealants joints are the most underrated joints but they are the important joints when it comes to…
Q: State AT LEAST TWO (2) corrosion prevention methods applicable to the steel tank. Examine the…
A: Storage Tanks There are two types of steel used to make storage tanks: carbon steel and stainless…
Q: What is a steam curing?
A: Answer:- Steam curing:- Steam curing is, steam curing in water vapor at atmospheric or higher…
Q: How Dry-laid-nonwoven fabrics are manufactured?
A: Dry-laid Nonwoven Fabric Manufacturing Process:
Q: Explain how ion exchange columns are typically arranged and operated when trying to meet a…
A: Ion exchange Chromatography : Ion-exchange chromatography which is designed specifically for the…
Q: 23: The beam shown in Figure 3 is subjected he moving load shown . Determine (a) the naximum…
A: Given Force exerted by rear axle =71.17 KN Force exerted by front axle =17.79 KN
Q: What are the various grouting materials ?
A: The different types of grouting materials used in construction : Cement Grouting:As the cement have…
Q: How to prevent retained austensite
A: By controlling the below parameters we can prevent retained austensite. It is very necessary in…
Q: Explain the significance of quality of bentonite slurry in the construction ofdiaphragm walls?
A: Bentonite slurry is one of the most common excavation fluid used in constructing diaphragm wall.…
Q: What is the lowest temperature at which mortar can be laid before requiring protection from…
A: If mortar is used below the lowest temperature it may not set properly and if water is retained in…
Q: How does runing water cause abrasion?
A: Answer : Running water can cause abrasion by the movement of sediment and debris carried by the…
Q: As a practicing engineer, you calculated the hydrostatic resultant on a vertical flat plate, 4.0 m…
A: Given:Top edge is submerged by 1 m of waterPlate is 4 m tall by 5 m wideRequired:Force on plate…
Q: Accessories for gypsum board construction.
A: Across all houses, gypsum board platforms have a critical function: fire safety. The gypsum board is…
Q: What will prevent bitumen from adhering to a concrete wall?
A: Bitumen is naturally occurring substance . As well as Bitumen is obtained as residue after…
Q: How can the cracking of any attached brittle materials such as concrete or plaster be prevented?
A: It is commonly believed that cracks are due to any foundation issues, although it is not always…
Q: What does a thermal break do
A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…
Q: Concrete Mix Design Problem: A concrete mix for 3rd level floor, open sided parking garage Given:…
A:
Q: SCC and Plain Concrete What is fly ash and why do we use it
A: To explain Self-compacting concrete and plain concrete Fly ash and its use Concrete is a…
Q: Some types of cementitious materials can set while exposed to air. True or false?
A: Cementitious materials are the building materials having binding properties to hold the entire paste…
Q: Site at least two construction situations where you want to delay the final setting time of your…
A: In the hot weather condition to counter the rapid hardening due to high temperature, the final…
Q: Explain the process of 'cracking' and discuss why it is done.
A: Cracking: It's the breakdown of the complex organic molecule into a simple molecule. The complex…
Q: 6. What is the difference between a maximum size aggregate and a nominal maximum size aggregate? 7.…
A: #6 what is the difference between maximum aggregate size and nominal maximum aggregate size??…
Explain the mechanics of frost wedging.
Step by step
Solved in 2 steps
