Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is a. rectified using a half wave rectifier circuit and connected to a 47.5 Q load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage.

Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is a. rectified using a half wave rectifier circuit and connected to a 47.5 Q load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consisting series connected a resistor and an inductance from a 70.7V (RMS), 50HZ sinusoidal AC source. The firing delay of the thyristor is 90° and the load values are R=102, L=0.1 H. Define the load current expression and draw the load current by calculating for first two periods. And calculate the average values of the load voltage and current.
In the circuit shown, a 5 V Zener diode is used to regulate the voltage across load Ro The input is an unregulated DC voltage with a minimum value of 6 V and a maximum value of 8 V. The value of R, is 6 2. The Zener diode has a maximum rated power dissipation of 2.5 W, Assuming the Zener diode to be ideal, the minimum value of Ro is 52. wwww R₂
High voltage
a. Prove that the efficiency of rectification in a full wave connection is twice that for half wave connection b. Use ideal diode model to analyze lo and Vo of both diodes. Prove the validity of the diode condition where Di is off and Dz is on for this circuit. 10 ka D 5 ka 15 V 10V c. Use your answer in Question 2a to derive the expression for transformer utilization factor.
is Idc -Idc 0 K de 27 If ripple-free load current in steady-state is assumed, the input current is waveform of the single-phase full-wave rectifier may then be depicted as shown in the figure above for an ideal input transformer. With the assumption that the supply is ideal and perfectly smooth and ripple free load current, which implies an infinitely large load inductance, it is quite straightforward to obtain an analytical expression for the input current harmonics. The rectangular wave is defined as when 0
In the figure given we have u(t)=10. cosot [V]. We assume the diodes and the A-meter (A) to be ideal. A u(t) a) Plot the waveform of the current flowing through the A-m in scale. b) What is the reading of the A-m, if it is moving-coil type? c) What is the reading of the A-m, if it is moving-iron type? d) Calculate the power factor of the WHOLE structure. R1 1 R2 102
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Using an ideal diode, design a clamper circuit that results in the desired output waveform as shown in Figure Q2b. Show overall analysis to justify the proposed design
Example 3:-
4i) For Single-phase half- controlled bridge rectifier shown in the figure : a formula for mean load voltage. 2. Draw the waveforms of Vo > issi,, i3, ių and io assuming highly inductive Load and d=45°. Co Us Dy in vord
Q2 A circuit with an unstable DC voltage source Vs and output Vzis shown in Figure Q2. The unstable DC voltage source has nominal 20V but it can vary as much as +/- 20%. The circuit contains a zener diode. The zener diode has voltage Vz = 7.2V when Iz 2mA, rz = 202 and its IzK = 0.5mA. Using the zener diode mode and without making further approximation, answer the following questions. Rs = 2502 Vz %3D Vs RL Figure Q2. a) Detemine RL such that Vz = 8V when Vs at its nominal level. b) Based on the result in a), determine the difference between the maximum Vz and the minimum Vz.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001