Example A beam AB span 4 m fixed at A and B carries a uniformly distributed load of 15,000 N/m as shown in Fig. (a). The support B sinks by 1 cm. Find the fixed end moments and draw the bending moment diagram for the beam. E = 2 x 105 N/mm², I = 8000 cm¹. 15,000 N/m 200 B

Example A beam AB span 4 m fixed at A and B carries a uniformly distributed load of 15,000 N/m as shown in Fig. (a). The support B sinks by 1 cm. Find the fixed end moments and draw the bending moment diagram for the beam. E = 2 x 105 N/mm², I = 8000 cm¹. 15,000 N/m 200 B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Loading system shown in Figure 4 is in equilibrium. Lengths of BC and AD are 5 m and 3 m respectively. The force 2 N at C acts along BC and force 5.8 N at C is normal to BC. Determine the following for the given loading system: (a). Sum of moments about A and, (b). Sum of moments about B. 10 N A 40⁰ 4N 58N D 5N 20 9.6 N Figure 4: Loading system с 2N
Question 5 A U-section cantilever beam that is 2 meters long, is exposed to a point load of 5 kN acting through the centroid of the cross-section at its free end. The direction of action of the point load is inclined to the horizontal z-axis at an angle of 0 = 35° as shown in Figure Q5. The second moments of area about the centroidal axes of the beam cross-section are given as l, = 7.570 × 10-6 m*, l, = 1.078 x 10-5 m* and Izy = 0 and the centroid is located at the point (z,y) = (60, 57.5) mm from the left most bottom most position on the cross-section. Determine: (i) The inclination of the neutral axis from the horizontal z-axis and (ii) The magnitudes and the sense of the maximum stresses on the cross-section y 10 mm 10 mm ț10 mm 100 mm Figure Q5 Z-Cross section Beam F = 5 kN 150mm
Determine the internal shear force acting at point C Determine the internal moment acting at point C
Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P2 = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm² and Acp = 9,280 mm². The distances between various points on the bars are shown in the figure. Determine the vertical displacements &, and ôp of points A and D, respectively. E1.5m 1.5 m 2.1 m – A P = 400 kN 2.4 m P2 = 360 kN F 0.6 m|
Problem (9.3): The steel compression strut BC of the frame ABC in Figure (9.26) is a steel tube with an outer diameter of do= 48 mm and a wall thickness of t = 5 mm. Determine the factor of safety against elastic buckling if a distributed load of 10 kN/m is applied to the horizontal frame member AB as shown. Let Est = 210 GPa and oy = 340 MPa. 10 kN/m В' 1m 2 m- Figure (9.26)
Determine the displacement at C of the beam in this Figure using Conjugate Beam. E- 29,000 ksi and I=600 in.
A part of slab is given in the figure. The slab is supported by secondary beams AB, CD and EF which are placed with a 50cm spacing. The secondary beams transfer the load they carry to the main beams.In the figure, AE and FB are the visible part of the main beams. Finally, main beams are supported by the columns at both ends. The slab is under uniformly distributed load q=4.5 kN/m2. The span length L is 3,5 m. Determine the dimendions of rectengular cross-sections of timber beams CD and the main beam which has a length of 4 m.
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
P11. Analyze the given indeterminate beam using the three-moment equation. Then draw the shear and moment diagram. EI is assumed to be constant.
Consider a 200-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 70 kN-m and 74 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume bq = 155 mm, b2 = 30 mm, b3 = 245 mm, d1 = 65 mm, d2= 200 mm, d3 = 65 mm. Determine the maximum horizontal shear stress in this segment of the beam. b1 b2 d2 MA MB |dz A B b3 Ax Answer: Tmax = i MPa
2.0 m ㅏ F 3.0 m q 4.0 m The above freely supported light uniform beam of length 10 m carries a point load F = 45 kN and a uniformly distributed load q = 23 kN m −1 at the positions indicated. Find the shear force V (x) and the bending moment M(x) at the following points along the beam. Give your answers correct to two significant figures. At the point x = 4 m the shear force and bending moment are: V(4) and M(4) = KN kN m. At the point x = : 8 m the shear force and bending moment are: KN = V(8) and M(8) = kN m 1.0 m + -+
Loading system shown in Figure 4 is in equilibrium. Lengths of BC and AD are 5 m and 3 m respectively. The force 2 N at C acts along BC and force 5.8 N at C is normal to BC. Determine the following for the given loading system: (a). Sum of moments about A and, (b). Sum of moments about B. 10 N A 40⁰ 4N 58N D 5N 20 9.6 N Figure 4: Loading system с 2N