e Uhe temp- of 2)3k kath that har 4 0:3 m A steel 3t is suddenly plunged * * + amp: 8 35oK. Etimete to nea ch ball has a dia . watin Cange Fme needed untu tomp 349.9k. 1OW/m2 k

Q: Ihe limiting s1zes of a neember of ground shaft are 21.980mm eend 21.95amm.mese are to fit th…

A: Draw the sketch of the assembly showing the limiting sizes.

Q: Both ends of the fixed (fixed) rod were mounted at 0 °C. Calculate the minimum diameter of the bar…

A: for solution refer below images.

Q: of he throaderd screw i 40 The load is 20O AN ond it does Rot rotale with the sanow dat is corried…

A: GIVEN:-Diameter of threaded screw: d=40mmPitch of threaded screw: P=8mmLoas: w=20KNDiameter of…

Q: A cylindrical hole is bored through a steel block, and a cylindrical piston is machined to fit into…

A:

Q: A thrust B journa 350N 0.25m B 0.35m 0.35m 0.15m 0.2m 0.Im P draw fbd

A: Draw free body diagram.

Q: Determine the energy loss in 300 m of new, uncoated 30.5 cm inside diameter cast iron pipe when…

A: b) Pipe length, L=300 m Inside pipe diameter, d=30.5 cm = 0.305 m Water temperature, T = 15oC Water…

Q: Solved using methods of members. Complete soution

A:

Q: Lind Osthogonal tsajctosies 6aX whese a pabometeb

A:

Q: Help in filling table: Material Yield Strength (MPa) Elastic Modulus-E (GPa) Poisson’s ratio…

A:

Q: 2. what is the reduction ratio, if D.-94mm, this means r=47mm=0.047m If pressure (P) = 45Mpa (45*106…

A: given data  initial diameter = 94 mm final diameter = 16 mm pressure = 45 Mpa.

Q: Determine O gn torques 6)7 mo

A:

Q: minimum cllowasle deign dianet

A: Given; A solid circular shaft needs to be designed to transmit;Torque,T=50 N-mAllowable shear…

Q: UDUT O Pumapal elsment direrton e Han shear dsmant disuction O At dructon 150 pom X Part -O By usung…

A:

Q: 3. If gage A reads -20 kPa, determine the elevations of points L, N, Q and 9. 2 El. 65.00t E Air El.…

A:

Q: A 2o0y bubble 7o mm diameten internal frlessure exces g 25 N/mim2 what in tension in soof Silm. has…

A: It is a basic problem on the surface tension.

Q: R. Im fui K2 The livee diplasoment Egr. Biffantil Egr en Emyy af the ystem akot pivt. 0. T Imi+ vở A…

A:

Q: G For venture meter experimeat, the di fherence between the ced pre urer waslos Kpa). the diometer…

A:

Q: 5m nas Taz ?

A: Given Data: Length of the beam, L=5 m

Q: A 10' C B 10' E 10' 10' 20 kips 20 kips 20 kips H vy K M 10' 10' 20 kips 20 kips 20 kips 10' N 15'…

A:

Q: is it correct?? if it is correct,please tell me why r=0,z=H??

A: We have given in the solution:To find:Whether the Boundary condition applied r=0,Z=H are correct or…

Q: Determine the maximum normal stress (in MPa) developed in the bar when it is subjected to a tension…

A:

Q: Question 3 Determine the no of revolertions bearing rototing at the rate 2 yns done by 6ohz in it it…

A: No. of revolution by bearing in 1 sec = 60

Q: Since the beam AB shown in the figure is P = 60 kN, L = 3 m and E = 200 GPa, find the deflection at…

A:

Q: of pressure include?

A: Given :- Standard of pressure .

Q: Given D 2KN ← 1m P 2 To Determine 0-3 1m (1-7 one • Diameters of the bars is 1mm e 3 3KN Youngs…

A: Consider elements connecting nodes 1 and 2 as Element-I and element connecting nodes 2 and 3 as…

Q: if Op1 is 18.6 °ccw, then Os1 is . CW

A:

Q: Una porticule musta un patron de uelocided V= 0,12 Vī5ut?-0.10 Ob tenga: - La posición a h 2s - La…

A: Velocity v=.121.56t2-.10 now since velocity is defined as rate change of position that means v=dsdt…

Q: QUESTION Determine the cooling load in a building at 16 hr and 19 hr caused by an electric Egg…

A: INTRODUCTION: The cooling load is the amount of power necessary to keep a place or item at a…

Q: (3)

A:

Q: For Ta pered pipe shown below, what is a as diameter of the pipe at

A:

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

A: Given data, DAC = Diameter of AC segment = 50 mm DCB = Diameter of CB segment = 100 mm TD = Torque…

Q: A 4-inch diameter cylinder moves a 25000 Ib load 24 inches in two seconds. Determine: a. The…

A: Given data,D=4instroke length L=24 inLoad =25000lbtime t =2s

Q: Question (1):- Find the pressure in the pipe shown in figure.if Pmer=13600kg/m' and pw=1000kg/m. 80…

A:

Q: Find the pressure ratio trif the temperature T 720 "K and T, 1167 "c Select one O a 21.1 Ob540 OC018…

A:

Q: Using the data provided on the figure below, determine: a. Water volumetric flow rate. b. Dynamic…

A: Given data, From the given figure Diameter of pipe at point 1, D1 = 6 in = 0.5 ft Cross-sectional…

Q: strbes a flet ghke as shown. The wuté Ieaves the noeele at lomls watr from from - statiny nozte the…

A: From Newton's second law of motion - Fjet=- FplateFjet=mvinitial-mvfinal= ρAv2-0 Because final…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.