Draw the shear force and bending moment diagrams of the cantilever beam shown using METHOD OF AREAS. Determine the maximum shear force and maximum bending moment. Note that there are internal hinges at C and E. A 15 kN/m 120 KN TTT c ↓ CONS 10 kN/m EIIII NEW SON FACROZ B D Hinge Hinge -8 m-5 m-+-5 m-+-5 m-+-5 m--8 m- G HIRE

Draw the shear force and bending moment diagrams of the cantilever beam shown using METHOD OF AREAS. Determine the maximum shear force and maximum bending moment. Note that there are internal hinges at C and E. A 15 kN/m 120 KN TTT c ↓ CONS 10 kN/m EIIII NEW SON FACROZ B D Hinge Hinge -8 m-5 m-+-5 m-+-5 m-+-5 m--8 m- G HIRE

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the shear value when x = 6m (from the left) for the beam shown Where: P1 = 61kN; P2 = 52kN; W1 = 13kN/m; W2 = 25kN/M 4 m P1 1 P2 w2 w1 42m²³4 3m R₂ 2m A B 1 m 5 m E
For the truss shown (A is a pin connection and G is a roller) solve for the force in members EF, FL, and KL. Be sure to indicate whether the member is in compression (C) or tension (T).
The bell crank as shown in the fig. is in equilibrium, determine the shearing force in the pin at D. Pls include formula, solution, and fbd. Thank you
1-7. Determine the resultant internal loading on the cross section through point D of the pliers. There is a pin at A, and the jaws at B are smooth. 20 N 20 N -120 mm- 80 mm 30° 40 mm 15 mm B
2-35* A steel bar with a 4 × 1-in. rectangular cross section is being used to transmit an axial tensile load, as shown in Fig. P2-35. Normal and shear stresses on plane a-a of the bar are 12 ksi tension and 9 ksi shear. Determine the angle 0 and the applied load P. P a
Calculate for the following member forces of the frame shown below using Portal Method. a. Shear at column FE, VFE in kN b. Shear at column ED, VED in kN c. Shear at beam FC, VFC in kN d. Moment at A, MA in kN-m e. Moment at girder KH, MKH in kN-m
H.W: Determine the external reactions at A and D for the roof truss loaded as shown 100KN BỊ 50 kN 100kN 50KN 60 60 60 30 A 10 m Activate Wind
Using the method of sections, determine the force in members BD, BE and CE. D F 50 kN В 4 m A H E G 3 m 3 m 3 m 3 m 40 kN 20 kN
SHOW COMPLETE WORK AND FBD
2. Find the force in bar CG using METHOD OF JOINTS. B C D 16' A 12'. H 8k -12' G ▷ V 2k -12'- F E 4k 3k
Q: Identify the zero-force members, and then find the force in members (CB, DE, CK, KL and EH) using method of sections. For each step, Draw the section and indicate all details. 100 kN 60 kN DV 60 kN E 12 m G M K H 6 m -6 m 6 m 6 m 6 m-6 m
For the lightweight truss which is loaded as shown 10 kN 5 kN 6 m -6 m VA VB C IT 4 m D -6 m 3 m 3 m By using the Vector Approach and the Method of Pins, determine the force in member BE (kN), by analysing joint B. Answer: