Determine the total deformation of a tapered bar with a thickness (t = 25 mm) as shown in thefigure, having E= 200 x 103MP a. The applied load in the given problem is P = 220 kN.25mm -B0mmP-220KN750mm

Answered: Image /qna-images/answer/fe1f3d85-d201-4d3b-9c56-a7318ec7d8b7.jpg

Determine the total deformation of a tapered bar with a thickness (t = 25 mm) as shown in the figure, having E = 200 x 10 MP a. The applied load in the given problem is P = 220 kN. 25mm B0mm P=220KN 750mm

Determine the total deformation of a tapered bar with a thickness (t = 25 mm) as shown in the figure, having E = 200 x 10 MP a. The applied load in the given problem is P = 220 kN. 25mm B0mm P=220KN 750mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. А) 12500-pi в) 6250*pi с) 3125*pi D) 1563*pi
3 The piece of plastic is originally rectangular. Calculate the shear strain Yxy at corners A and B if the plastic distorts as shown by the dashed lines. 2 mm 300 mm 2 mm D -400 mm- mm, B A 4 mm 72 mm 3 mm X
Question 3 A pair of lateral load is applied to a 3 m steel beam as in Figure Q3a to bend it plastically. The beam has a solid rectangular cross-section (30mm x 50mm) as in Figure Q3b. The steel behaves in elastic-perfectly plastic behavior with Yield Stress of 200 MPa. When 50% plastic condition at critical section, determine: a. the value of load P b. the Yielded Length, Lp corresponding to condition in part (a). 1.5P P 1m 1m Figure Q3a 1m 30mm 50mm Figure Q3b
PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar. Torque T=1100N.m acts at the free end of the bar. Both the bar and tube are made of an aluminum alloy with shear modulus of w ww elasticity G=27GN/m². Given that dl=35mm, d2=45mm, d3=60mm, d4=70mm. Determine the following: a. Maximum shear stress in both the bar and tube b. Angle of twist at the end A of the bar. (In degrees) Tube Fixed plate End plate Tube d3 d1 d2 d4 Bar Cross-section of the bar and tube
Situation 6: The rigid bar of negligible weight is supported as shown in the figure. If W = 120 kN, There is a temperature change occur in the assembly and cause a tensile stress of 55 MPa in the steel rod. Use the following data: Bronze steel 1 m - 2 m O 4 m W 2 m 3 m 16. Compute the axial stress at bronze rod 17. Compute for the change of temperature 18. Compute for the vertical deflection at the W Steel Rod Bronze Rod A (mm²) 320 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
Question 2) Find the shear center of the section below and calculate the maximum shear stress that occurs in the section as a result of the loading shown in the figure. The section thickness is uniform everywhere and is 10 mm. Note: G.M is the geometry center of the section, the shear force of 40 kN acts from the geometry center of the section. You can look at your lecture notes for the coefficients you will need. 160 mm V-40 kN t LG.M 100 mm
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm
A rectangle column 500 mm x200 mm in cross-section is subjected to a compression load 1000 KN, the stress on the column is: a. 30 MPa b. 10 MPa C. 50 MPa d. 20 MPa
For the assembly shown in the figure below, Determine the state of stress at point A on the cross section of the pipe at section a-a. 20 mm P 170N d 30mm Section a-a 120mm b 220mm
FE.Question 3