Determine the missing distance of line 1-2, determine the missing distance of line 4-1.

Q: Fundamentals of Surveying All azimuths are measured from South. All angles must be written to the…

A:

Q: If the surveyor is at Point A, and recorded the location of Line AB to be 200 degrees 35 minutes in…

A: Given data Angle of line AB = θAB = 200°35' Angle of Line AC = θAC = 280°15' Length of line AB (LAB)…

Q: The process of determining relative elevations of points on the surface of the ground is known as a.…

A: Surveying may be defined as the method of making measurements of relative position on the surface of…

Q: Item 3 A highway survey PI falls in a pond, so a cut off line AB= 275.21 ft is run between the…

A:

Q: Line AB has an azimuth of 322° 40' 20" (origin point is B). Find the principal angle in degree for…

A: Given data : Line AB has an azimuth of 322° 40' 20" Find the principal angle in degree for line AB

Q: Q2- In the traverse ABC, the coordinates of points A and B was (200,400) and (350,200) respectively,…

A:

Q: 15. A surveyor needs to know the distance between points C and B as shown in Figure D. A building…

A:

Q: Subtract 103° 32' 00" from 44° 52' 35" and provide answer as the equivalent positive angle in…

A: Given data- Two angles are given 103o32'00" & 44o52'35" To Find- It is needed to subtract…

Q: Find the area of the lot using the given data.

A:

Q: Determine the interior angle at point D. 184° R BV A D a. 135 degrees b. 135 grads c. 250 degrees d.…

A:

Q: Traverse) and Recorded the following results, the length and deflection angle of each line:  AB=…

A:

Q: Plot the traverse listed below: Line AzimuthS АВ 225 degrees ВС 225 degrees CD 301 degrees DE 301…

A:

Q: POINT NORTH/SOUTH DEGREES MINUTES EAST/WEST DISTANCE (M) 0-1 19 21 E 530.49 1-2 N 81 21 w 23.59 2-3…

A: Given, POINT LENGTH (L) BEARING (θ) LATITUDE=Lcosθ DEPARTURE= Lsinθ 0-1 530.49 S19°21'E -500.52…

Q: Using the data below, compute the area of the lot. Included Chord Distance Length of side (m) Angle…

A: Base of each triangle will be 10 m And heights of triangle can be taken as corresponding chord…

Q: The following offsets are taken from a survey line to a curved boundary line: Distance (m) 5 10 15…

A:

Q: A polygon has the following interior angles: 135°, 135°, 148°, 90°, 178°, 80°, 180°, 60°, 72°. Will…

A: Given data, Interior angles of a polygon are 135°, 135°, 148°, 90°, 178°, 80°, 180°, 60°, 72°

Q: Points C and D have the following coordinates (Northing, Easting). C = (800, 600), D = (450, 350).…

A:

Q: 11. If the balanced latitudes and departures are given for the following traverse, what are the…

A: Given data- To Find- The coordinates of the remaining two points.

Q: Given the following data on the table. Fill up the needed data. Balance the traverse by transit…

A:

Q: A circle of radius 832.05 ft, centered at point A, intersects another circle of radius 1000.40 ft,…

A:

Q: Problem. The coordinates of the loop traverse are given below. a. Compute for the bearing and length…

A: Calculate length using formula L=(∑Latitude)2+∑(Departure)2 Calculate bearing using formula…

Q: 3700 500 3850 450 B 2700 450 630 3820 4 2900 175 1 3 А 2

A: The staff reading taken firstly as back is termed as Back sight (B.S.) The staff reading taken in…

Q: the following offsets are taken from a survey line to a curves boundary line, and the first and the…

A:

Q: 5. A closed traverse has the following data. | 等 LINE 1-2 2-3 LATITUDE +76.30 +33.80 DE PARTURE…

A:

Q: 1. PROBLEM 1. A lot in the form of a convex polygon has the following technical description. The…

A: Given, Line                 length                        bearing  AB                   525.36…

Q: The following interior angles of a triangle were measured with the same precision. No. of…

A:

Q: Find the are circle

A:

Q: Which line passes through true north and true south? O a. Dip O b. True Meridian c. Magnetic…

A: Following is required  answer :

Q: LINE DISTANCE BEARING AB 60 N15°30'E BC 72.69 S82°23'E CD 44.83 S17°30'E DE 56.45 S70°36'W EA 50…

A:

Q: what is the following: (in meters) 1. Length AB 2. Length BC 3. Length CD 4. Length DE

A:

Q: 1) The measure of the missing angle in the triangle below is 95 35

A: A triangle is a type of polygon which is having three sides and three vertices. It is the smallest…

Q: STA 8+50 elevation = 132.74 %3!

A: According to given datafor STA 8+50 Elevation=132.74STA 12+ 50 Elevation = 246.29To calculate the…

Q: 7. This rule of determining area is based on the assumption that the curved boundary consists of a…

A: In a geometric pattern, a refractory piece is examined and sorted on graph paper. The building area…

Q: -18- (45.52) (40.00) 5000.00 ft N 10,000.00 ft E 4990.54 ft N 15,665.34 ft E (b) Exercise 4 5.…

A: Solution This can be analyzed on the basis of proportioning of distances in the fields using…

Q: Q.4. Compute by DMDs the area in hectares within a closed-polygon traverse ABCDEFA by placing the X…

A:

Q: Q1- Draw the Profile Leveling with suitable Horizontal and Vertical Scale? A Station 0.00 10.00…

A:

Q: From the information shown in the following table, find the magnitude of the local attraction line…

A: in the close polygon the part point will be meet with the first point so their is the side FG must…

Q: The area bounded by curve y? = 16x and line x - y + 3 = 0 is. %3D

A:

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.