Determine the maximum torque that can be applied to a hollow circular steel shaft of 102mm outside dia. and 71 mm. inside dia. without exceeding a shearing stress of 58 x 10° N/m2 or a twist of 0.45 deg/m. Use G = 84x10° N/m2. Add 9 in the outside and inside dia. only. Example: D = 102 +9 = 111mm, d = 71 + 9 = 80mm. Show the complete and legible answer.

Determine the maximum torque that can be applied to a hollow circular steel shaft of 102mm outside dia. and 71 mm. inside dia. without exceeding a shearing stress of 58 x 10° N/m2 or a twist of 0.45 deg/m. Use G = 84x10° N/m2. Add 9 in the outside and inside dia. only. Example: D = 102 +9 = 111mm, d = 71 + 9 = 80mm. Show the complete and legible answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A portal frame shown in figure (not drawn to scalé) has a hinge support at joint P and a roller support at joint R. A point load of 50 kN is acting at joint R in the horizontal direction. The flexural rigidity. El, of each member is 106 kNm². Under the applied load, the horizontal displacement (in mm, round off to 1 decimal place) of joint R would be 5 m Q El El 10 m 50 kN
Question 1 The same torque is applied to two tubes with identical metal sheets, determine the ratio of T circle/Tsquare of the shear stresses. Given: r= 14 mm, S = 19 mm, and t = 2.84 mm. 43 FETOO KA F1 F2 FS FB F7 F8 ESC T H.
NEED IN 1 HOUR PLEASE THANK U A hollow steel shaft 10 ft long must transmit a torque of 250,000 lb-in. The total angle of twist in this length is not to exceed 2.5 degrees and the allowable shearing stress is 12,000 lb/sq.in. Determine the inside and outside diameters of the shaft if G = 12 x 106 lb/sq.in. The action is elastic.
10
Ql:- The system of gears B and C take out power 150 and 175 hp respectively from a motor A that has 325hp, Find the shaft dimeter if the allowable shear stress is 6250 psi and the angle of twist between gear C and motor is 2 degree. Let G=11.5 x 10° psi. Gear Gear Motor A B
#2 will upvote anyone who will answer correctly. Thanks
Calculate for the axial force in kN at member DC of the frame shown in figure 2 using Cantilever Method. Enter absolute value and use 2 decimal places in your solution. a = 49.5 kN, b = 32.8 kN, c = 4.2 m "a" kN H wwww "c" m "b" kN C K ww. "c" m "b" kN F "c" m 4 m 5 m A = 40 x 106 mm2 A. = 60 x 106 mm? A = 40 x 106 mm² FIGURE 2
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11800 psi, and the vertical deflection of joint D is not to exceed 0.600 in. when a load of P = 2900 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 92 in., b = 40 in., and c = 34 in.
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 9600 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 2800 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 62 in., b = 22 in., and c = 24 in.
WHICH OF THE FOLLOWING GIVES SHERARING STRESS IF a=3inches Which of the following gives the minimum permissible dimension if the shearing stress is limited to 6000 psi
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11000 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 3300 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 94 in., b = 22 in., and c = 32 in.