Deter mile State spo ce rehg1esentection O/p > 3) 4Nm 3N-m 3N/p fits + 3 kg 3 N/m 3N-S/m 2 N-5/m IN-/m

Q: 1) Pitot tube can be used to measure the flow velocity. The equation can be derived from Bernoulli…

A:

Q: From the below given graph for venturimeter experiment the value of A is 5.05 and the value of B is…

A:

Q: Make an isometric drawing based on the flowchart of the figure, where: PSA GEN = Pressure Swing…

A: Hey dear):-can upload the question again . It is incomplete now .thank you ):-Explanation:

Q: Exus S.fd and Bomid? Draw YKN/m AX=0, 3m

A:

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: * The unit of measurement for torque is

A:

Q: A Newtonian fluid having a viscosity of 0.38 N. s/m2 and a specific gravity of 0.91 flows through a…

A:

Q: Please help to correctly solve all parts.

A: Step 1:Matching each case with the appropriate flow meter:1. Gasoline flow in a gas station: Rotary…

Q: What is the horsepower of the pump? 1 -10⁰ Area = 1 =qift so' hf thm - zcas

A:

Q: 1. Fig. 1 shows a simple six bar linkage held in static equilibrium while a force P= 750 N is…

A:

Q: SAE 10W30 motor oil is used as a lubricant between two machine parts. 4 lbf.s f+² Assume μ = 1 x 10²…

A: Given that :                  Viscosity            Velocity difference     Maximum shear stress

Q: A RWD Formula SAE car is given with the following information m = 600 lbm (including the driver), l=…

A:

Q: Q2) a horizontal air conditioning system as shown below consists of 90-degree elbows (K=0.3) and a…

A: the pressure at the inlet should be enough so that it can overcome the frictional head losses and…

Q: An industrial process involves the measurement of the flow rate of water in a pipeline using an…

A:

Q: Determine the brake power and brake thermal

A: Given data, A large four stroke  cycle diesel engine runs,N= 2000 rpmEngine has a displacement of 25…

Q: Identify the measuring unit which is having nonlinear relationship between pressure difference and…

A: Answer:

Q: Q1/ Convert the temperature in Parts (a) and (b) and temperature intervals in Parts (c) and (d): a)…

A: To convert temperature in different scales we have to familiar with the relation between the…

Q: Looking for the calculations / unit analysis for ... 1.) Inlet Potential Energy 2.) Outlet…

A: Given that, Rate of water, Q=60 GPM,Diameter of water, D=2 in,Elevation of pipe, h=100 ft,Pressure…

Q: Manometer containing mercury was used to find the pressure in the pipe containing water as shown…

A:

Q: The truck shown below weighs 16 tonnes when empty. The truck has a capacity of 36 m volume for the…

A: Given               Weight, W = 16 ton Specific gravity, SG = 0.85               Volume, V = 36 m3…

Q: lq * (0.000001 84)] v = TT * q- Flow rate (STB per Day) v- Fluid velocity within pipe d- Pipe…

A: The nature of flow whether it is laminar or turbulent is determined by the Reynolds number which can…

Q: 11/100 mm in size and 1100 kg/m3 in a cylindrical container with a diameter of 11 m density of 100…

A:

Q: Perform the following unit conversions. a) ΔT = 85°C to Kelvin, Fahrenheit and Rankine b) ΔT…

A: Given Data a) Temprature in 'C= 85'C                   b) Temprature in 'R = 150'R   We have to do…

Q: If the calculations lag behind the flow of fluid, what factor of the simulation gets affected? a.…

A: Explanation: 1)If the design calculations of fluid flow which are calculated by conventional…

Q: The unit for water flow meter ( rotometer) used in cooling tower expeiment is liters per second.…

A: A rotameter is a flow meter which is use to measures volumetric flow of liquids and gases.

Q: b) Table 2 shows the free delivery and shut off points of the individual data for pump A, B and C.…

A: Write the given data. For Pump A,QA=20 m3/shA=4 mFor Pump B,QB=15 m3/shB=6 mFor Pump C,QC=35…

Q: Place the correct formula in the blank %To determine Generated Power Output of Wind turbine

A: Given:- Wind turbine:-   To find- Power formula

Q: The length where the shear is zero (x) (if applicable) • The maximum shear load (Vmax) – positive…

A:

Q: A horizontal pipe has a sudden contraction from DN100 to DN80 Schedule 40 steel pipes. The water…

A: Since we only answer up to 3 subparts, we will answer first 3. Please resubmit the question and…

Q: Given data: U-2 m/s a-3.3 m/s2 Find final velocity

A: Find the final velocity .

Q: C2(i)Assume that annual energy requirement of an industry is 20900 kWh ,we calculate that what will…

A: Given  Annual energy requirement= 20900kWh Coefficient of performance = 0.4 Loss factor value =…

Q: Q2. The pressure in a gas pipe is measured by a mercury manometer as shown in the figure. One leg of…

A: Given : manometer reading x = 450mm of mercury barometer reading h = 755mm of mercury

Q: Total pressure port (in) port m (0) Col A pitot-static pressure probe (see Fig. 9.28, and the…

A: For the solution refer below images.

Q: Magnolia Dairy Products plant must cool 4000 gallons of fresnmilk received from the farm per day…

A: As per given  Plant cooled=4000 gallon Spefic gravity =0.935 Temperature difference =80 to 38 °F…

Q: A fluid (SG = 1.3) flows from a nozzle. The nozzle is 15m above the datum. The power on the nozzle…

A:

Q: Consider the air flow over the wing of a civil airliner flying at M, 0.85 and at an altitude of…

A: Free stream mach number = 0.85 (given) Isentropic relations are used to arrived the solution.

Q: Referring to the figure shown below, water contained in a piston-cylinder assembly, initially at 1.5…

A:

Q: for one of the 6 un-filled out problems. a) Based on the representative boundary conditions shown in…

A:

Q: If a group of forces affects a particular structure, the structure will be in equilibrium if the sum…

A: To choose: The correct option. (a) Explanation: The equilibrium of body is a state of the body when…

Q: Q2: Explain the procedure of venture meter experiment.

A:

Free undamped vibrations

Whenever an object/system displaces in either side of its equilibrium position with the help of an external/internal means, then the object/system moves regularly or randomly on both sides of its equilibrium position. This motion is called vibration. Generally, there are three types of vibration: longitudinal vibration, transverse vibration, and torsional vibration.