Design a second order LPF, with unity de gain, to realize the following natural modes P1,2 = 10¹ (cos(144⁰) F jsin(144°)) based on method of inductor replacement i.e. (Antoniou inductance simulation cct.). Select appropriate components values and plot the final circuit, assign the values of the components on the circuit diagram, and write the resulted T (s). chop

Design a second order LPF, with unity de gain, to realize the following natural modes P1,2 = 10¹ (cos(144⁰) F jsin(144°)) based on method of inductor replacement i.e. (Antoniou inductance simulation cct.). Select appropriate components values and plot the final circuit, assign the values of the components on the circuit diagram, and write the resulted T (s). chop

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

INDUSTRIAL ELECTRONICS
DC DC Converters a) A step-up PWM converter has the following data: V = 8 V, Vo = 24 V, lo = 1.25 A, and f = 200 kHz. Calculate the minimum inductance required for the converter operation in CCM (Continuous Current Mode). Then, determine the required capacitance for the converter. Assume n = 100 %. b) Design a boost SMPS converter to meet the following specifications: V = 80 V, Vo= 400 V, R. = 480 n, f.= 25 kHz, VNOS 1%. Find L, C, minimum inductor current lupin), maximum inductor current tunan), and output power. Then, sketch the inductor voitage and current waveforms for one cycle.
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/2. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state: i. Draw the converter circuit. ii. Determine the inductor's turn ratio. iii. Determine the primary inductance. Sketch the diode current and switch current. iv V. Find the peak and mean of the switch current.
The dc converter shown in the next figure is used to control power flow from a dc voltage, Vs = 150 V to a battery voltage, E = 250 V. The power transferred to the battery is 30 kW. The current ripple of the inductor is negligible. Determine (a) the duty cycle K, (b) the effective load resistance Req, and © the average input current Is. L Vs + VL iL DI + Chopper E
Q2] For the circuit shown below, when the switch closed at =0 and by assuming zero initial charge on the capacitor terminals. Do as required: a. Find the transient current equation w.r.t. time. b. Identify the state of cireuit. c. Find Neper frequency, resonant radian frequency, damping radian frequency, and natural radian frequency d. The value of "C" that makes the circuit as critically-damping. 1002 0.3H 200V 75µF Vc
Analogue 2
Hononta (Vj Ais M QUESTION (1) pressure signal from a force transducer is given as under. Analyze it in terms of harmonics, amplitude, circular frequency, cyclic frequency, time period and phase. A. P=15 sin(20m + +12 sin(40t-)+10sin(60t +)+8sin(100zt +")+5sin(140nt -"). +3sin(180) Pa %3D
ne Q.15: The switch has been in position a' for a long time. At t-0 the switch is moved to position "b". Use classical method to find the voltage across and current through the capacitor as a function of time? (Ans.: Vc(t)=80[1.25-es t%=0 S 30V 452 100V 2uF 5000t (cos5000t+sin5000t)] V & ic(t)=1.6e 5000t sin5000t A)
6. Consider the circuit depieted in the figure below, R V,eiut where we shall assume that the input voltage can be written as Vin(t) = Re{Voet} with complex-valued Vg, and likewise that the output voltage Vout(t) = Re{Vje*} with complex-valued Vị. With j = V-1, the complex impedances of resistors, ca- pacitors, and inductors in this case are respectively given by ZR = R, Zc = ZL = jwL. (a) Determine Vı/Vo as a function the angular frequency w given the parameters R and C. (b) Evaluate Vi/Vo in the limit w +0 and in the limit w + o0. Is the circuit above a low-pass filter, a high-pass filter, or something else? w
Draw a clearly labelled equivalent circuit showing the straycapacitors.
9. PLOT. Plot the sine wave at frequency fm and the sampling signal at frequency fs1. Write a MATLAB program to take input both fm and fs1 and plot the curves mentioned above.,.
3) Load for a circuit with direct current source voltage The waveform of the voltage generated on it is below shown. Source for this working circuit that is symmetrical The value of the voltage and load resistance is 100 V and 5Ω respectively.It is given as. Find what is required below. d) Find the effective value of the output voltage e) Total harmonic distortion in output voltageCalculate (THD)