Design a combined footing to support two columns spaced 18 ft apart, and left column carries total load of 350 kips(40% live load) and right column carries a total load of 400 kips(40% live load). The left column is centered 1 ft from the property line and both columns are 24 in.x18 in. in cross-section. The allowable soil bearing pressure is 5000 psf. The bottom of the footing will be 6 ft below grade. Design the combined footing for these columns using fe=3000 psi, fy=40,000 psi. [Note: No need to design in the transverse direction].

Design a combined footing to support two columns spaced 18 ft apart, and left column carries total load of 350 kips(40% live load) and right column carries a total load of 400 kips(40% live load). The left column is centered 1 ft from the property line and both columns are 24 in.x18 in. in cross-section. The allowable soil bearing pressure is 5000 psf. The bottom of the footing will be 6 ft below grade. Design the combined footing for these columns using fe=3000 psi, fy=40,000 psi. [Note: No need to design in the transverse direction].

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

?CE
A 3 m square footing supports a vertical column load of 200 kN and two moment loads with axes parallel to the sides of the footing, each having a magnitude of 124 kN-m. The embed-ment of the footing is 1 m, and the groundwater table is at a great depth. Determine whether eccentric loading requirements will be met. If these requirements are not met, determine theminimum footing width, B, needed to satisfy these requirements.
I need correct solution Solution in chegg was incorrect So please provide correct solution
A square footing, 1.7 m x 1.7 m, is to be founded at a depth of 1.4 m below the ground surface of a deep clayey sand stratum. The saturated unit weight of the soil is 17 kN/m3. Based on drain triaxial tests, the soil parameters are c' = 7 kPa and ø' = 25°. The ground water table was found at the surface level. The foundation is to carry a permanent load of 280 kN and a variable load of 210 kN.
Please explain and number steps
A proposed building column will carry a downward maximum unfactored load combinationof 250 k and a service load of 185 k. This column is to be supported on a square footing at adepth of 7 ft in a silty sand with the following engineering properties: g = 119 lb/ft3above the groundwater table and 122 lb/ft3 below, c′ = 0, f′ = 32°, N60 = 30. The groundwater tableis 15 ft below the ground surface. The allowable settlement, da, is 0.75 in. The ASD, factor
Design a circular footing for a short circular column of diameter 350 mm carrying a working load of 1500 kN. Use M25 grade concrete and Fe500 grade steel. Safe bearing capacity of the soil is taken as 200 kN/m2.
A building will have a factored column load of 300 kN. The column is to be supported on a square spread footing underlain by a soil with the follow properties: c' = 5 kPa, o' 35°, y = 18.5 kN/m³. The groundwater table is at a depth of 15 m and the footing will be located 0.5 m below the ground surface. Determine the required footing size if Þ = 0.5. Use Terzaghi's bearing capacity equation for a square footing. Solve for 'B', making sure to use the reduction factor Þ; trial and error is the easiest way to solve for 'B'. Recommend a "reasonable" dimension for construction/design purposes.
A 200 mm wide concrete block wall carries a factored vertical design load of 172 kN/m. Thesustained load for settlement is 130 kN/m. It is to be supported on a continuous footing madeof 18 MPa concrete and 280 MPa steel. The soil has an allowable bearing pressure for bearingcapacity of 180 kPa (using LRFD methods) and an allowable bearing pressure for settlement of 110 kPa. The groundwater table is at a great depth. The local building code requires that the bot-tom of this footing be at least 500 mm below the ground surface. Determine the required footing, width, thickness, and design the lateral and longitudinal steel. Show your design in a sketch.
1- Design an appropriate footing/footings to support two columns A and B spaced at distance 2.1 m center-to-center. Column A is 20 cm × 30 cm and carries a dead load of 200 kN and a live load of 100 kN. Column B is 20 cm × 40 cm in cross section but carries a dead load of 300 kN and a live load of 150 kN. Width of footing is not to exceed 1.0 m, and there is no property line restriction. Use f- 28 MPa, f- 420 MPa, q all (net) =200 kN/m², ysoil= 17 kN /m³, and Dr=2.0 m.
A 12 in wide concrete block wall carries an unfactored vertical design load of 25.1 k/ft. The sustained vertical load for serviceability analysis is 18.4 k/ft. It is to be supported on a continu-ous footing made of 2,500 lb/in2 concrete and 40 k/in2 steel. The soil has an allowable bearing pressure for bearing capacity of 6,700 lb/ft2 (using ASD methods) and an allowable bearing pressure for settlement of 4,000 lb/ft2 . The groundwater table is at a great depth. The localbuilding code requires that the bottom of this footing be at least 24 in below the ground surface.Determine the required footing, width, thickness, and design the lateral and longitudinal steel.Show your design in a sketch.