(Dead & live)Find the maximum Service loads that the+₂²seam shown below can carry; if fé= 30 №by = 400 N/m², the ratio ofLive load to Dead loadis "2" (=—=—=2), Neglect beam self weight, if:Ⓒ As = 2000 min?2. As = 3000 mn?W=?L=4mL=2DWaW₂= 1·2D4+1-GL-LW₁ = 1.2 D-L+1.6x2D200mm12.400I loo300100

Given: fc = 30 MPa fy = 400 MPa LL = 2 DL hf = 100 mm bw = 200 mm b = 400 mm d = 300+100 = 400 mm…

(Dead & live) Find the maximum Service loads that the seam shown below can carry; if fé= 30 № Live load to Dead load by = 400 N/m², the ratio of mmz is "2" (=—=—=2), Neglect beam self weight, if: Ⓒ As = 2000 min? 22. As = 3000 mu? W=? L=4m L=2D Wa W₂= 1·2D4+1-6G L-L W₁ = 1.2 D-L+1-6x2D 200mm 12. 400 2 I loo 300 100

(Dead & live) Find the maximum Service loads that the seam shown below can carry; if fé= 30 № Live load to Dead load by = 400 N/m², the ratio of mmz is "2" (=—=—=2), Neglect beam self weight, if: Ⓒ As = 2000 min? 22. As = 3000 mu? W=? L=4m L=2D Wa W₂= 1·2D4+1-6G L-L W₁ = 1.2 D-L+1-6x2D 200mm 12. 400 2 I loo 300 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please need answer thank you
Dont round off in solution, only round off in final answer in 2 decimal places. Answer asap
Find the safest value of load "P" for the beam loaded shown. fc'=35MPA, Use GRADE 420 steel bar and n=10 The answer is kN. Assume unit weight of concrete = 24kn/cu.m. 200 3 m 1 m toort twit 3P 70 200 2-20 mm O 330 3. BEAM 4-32 mm Ø 300 100 DIMENSIONS ARE IN "mm"
a) Design the cantilever beam shown below. Assume p-0.005, bw-25cm and d=3cm. Use C20 concrete and 5420 steel. Select 20 bars. b) Using your selection in part(a) and assuming 10 bars for stirrups, 2cm clear concrete cover on the sides and max aggregate size as 25mm check if you can place the bars as a single layer. c) Using your answers for parts (a) and (b), draw the cross-section of the beam with reinforcement and dimensions. Use 12 for hanger bars and 10 bars for stirrups. DL= 33 kN/m LL= 15 kN/m 2.9 m
Given that the Gerber beam is drawn. Calculate and draw SFD,BMD,NFD Note : 1 ton = 1000kg Solve max in 25-30 mintes thank u
(1) PLZ pabeid 12 ft 19" 28" WOL= 1 KLF, not including self-weight PL₁= 10 kips PL₂= 6 kips fé = 3000 psi, fy= bo ksi NWC. #4 tied bars. Please design the Rebars. Show the bans displacement 2 Location.
A 100 X 100 mm in cross- section and 400 mm log is lbaded to failure by either two loads applied at the third pointc. Determine the compressi ve strength I f'c). a con centrated load at midspan or by fr = 0•62 L [ f!c (modulus of rupłure D CNSCP $ pees) fr is dctermined by flexural fr MorC GMcr for formula fr: %3D where, b= width h= height of Mcr = cracking of beam beam moment %3D
Question 1 A da tw M- Determine the section modulus for the below type of I-beam: https://www.engineersedge.com/materials/aisc W.S.M.HP Shapes of- (de)- (det) 11- TH W36X210 61.8 36.7 0.83 12.2 1.36 SH 2.31 2.3125 1.25 32.125 BM T रूम Calculator Section Modulus 1 Beam Un Calculator NA indicates neutral structural shapes/aisc structural shapes viewer.htme Use the information from the above web site link. Enter the value from the table (Sx) in in^3
Determine the losses in the post-tensioned concrete beam as shown below. 560 mm Given: POST-TENSIONED BEAM with A PARABOLIC TENDON PROFILE Span Length = 20 m fi = 1200 N/mm² A, = 2850 mm² Ac 4.23x105 mm² 1=9.36x10¹0 mm e-560 mm (@midspan, from N.A.) fc= 40 N/mm² Es = 210,000 N/mm² μ = 0.19 K = 0.0005 (per meter) Anchorage slip = 5 mm (jacked at left-end only). (make sure to draw the force variation diagram for anchorage slip) V/S= 6 RH = 70 Dead Load 9.97 kN/m fpy = 1714 N/mm² Bridge Width III
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
1. For the beams described below, determine the nominal capacity oMn Assume f'c = 4ksi fy = 60ksi Clear cover = 2 inches a) 3 No 6 Pmin=0.0033 Pmax=0.01806 b = 8in h=20in b) b=5in h=16in 4 No 3