Consider Two same size PV Modules which are connected in Parallel. The specification of each module is given as: Number of cells = 36, Area of each cell is 12 cm x 12 cm. (Assume the necessary data) Choose from the following the correct statement. a. The output voltage of this panel is 18 V, the output power is 155W b. The output voltage is this panel 18V, the output power is 75W c. The output voltage is this panel 36 V, the output power is 155W d. The output voltage is this panel 36 V, the output power is 75W

Consider Two same size PV Modules which are connected in Parallel. The specification of each module is given as: Number of cells = 36, Area of each cell is 12 cm x 12 cm. (Assume the necessary data) Choose from the following the correct statement. a. The output voltage of this panel is 18 V, the output power is 155W b. The output voltage is this panel 18V, the output power is 75W c. The output voltage is this panel 36 V, the output power is 155W d. The output voltage is this panel 36 V, the output power is 75W

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Briefly explain how to came up with your answer to each number and please show your complete solution. I want to learn how to solve this problem. Thank you!!
60 V D1 D2 2 kohm DA D3 -60 V Assume that an input signal is applied to the circuit given above, as shown in the figure next to it. Accordingly, answer the following questions. The diodes used are silicon diodes, their operating voltages are 0.7 volts, and can be omitted because their resistance is very small. Calculate V p-out( Vm ) for this circuit.
A full-wave bridge rectifier is to be designed to produce a peak output voltage of 10 V, deliver 100 mA to the load, and produce an output with a ripple of not more than 7.5 percent. Assume that the frequency of the source is 50 Hz, and that a constant drop voltage model with Vp = 0.7 V is t of used. D1 D2 vs(1) RL vz(?) D3 D4 Source Rectifier Load a) Calculate the needed value of the load resistor R1. 1 b) Calculate the peak value of the voltage source which should be used V (t). [ c) What will be the value of the ripple voltage V7 [ d) Calculate the value of the required capacitor C. [ e) Explain in your own words the difference between the output with and without using the capacitor in the circuit above.
*Use 4 decimal places. For the circuit below, determine the diode voltages VD1 and VD2, diode currents Ip1 and Ip2, and voltage across the resistor, VRLIMIT- Assume r'a (for both diodes)=200. Note D, is Germanium, D2 is Silicon, VBJAS = 22V and RLIMIT = 2 kohms. VD1 = 0 V; VD2 = 0 V; Ip1 = Blank 3 mA; Ip2 = Blank 4 mA ; VRLIMIT = Blank 5 v Use ideal model. Capture3.JPG +VD1- +VRLIMIT +Vp2- Ip2 VBIAS 두
a. What is the effect of applying reverse voltage on a pn junction? b. What is the critical electric field and when will it happen?
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
Solve it quickly please
Base on the data what can you conclude
ANSWER THE QUESTION
IN ALL CALCULATIONS AND THE USE OF THE FOUND VALUES IN THE EQUATIONS, THE PROCESS WILL BE MADE WITH 3 DIGGERS AFTER THE COMMA. Thank you
a) Determine the output voltage for all input voltages values. b) Sketch the overall output waveform, Vo(t).
Supply AC = 24Vp (peak) at 60Hz Diodes = Silicon Load Resistance = 1000 ohms