Note : Use virtual work method. Problem 8.34Consider the beam shown in (Figure 1). Assume the support at A is apin and C is a roller. Take E= 200 GPa. I = 150(106) mm¹.Suppose that w = 17 kN/m.Figure< 1 of 1 >1.0= MSubmit✓ CorrectPart BOB=Determine the slope at point B measured clockwise from the positive axis. Use the method of virtual work.Express your answer using three significant figures.SubmitPart C()Previous AnswersAB=Submit[45] ΑΣΦ | |Request Answer■μÃValueRequest Answervec< Return to AssignmentDetermine the displacement at point B measured downward. Use the method of virtual work.Express your answer to three significant figures and include the appropriate units. Enter positive value if the displacement is downward and negative valueif the displacement is upward.AC [w] ?UnitsProvide Feedback?rad< 6 of 6>Review

Find slope and deflection at B using virtual load method

Consider the beam shown in (Eigure 1). Assume the support at A is a pin and C is a roller. Take E = 200 GPa. I = 150(106) mm¹. Suppose that w 17 kN/m. Figure < 1 of 1 > ..-(#) # 1.0 M Submit ✓ Part B Correct OB = Determine the slope at point B measured clockwise from the positive axis. Use the method of virtual work. Express your answer using three significant figures. Submit Part C Previous Answers AB= IVE ΑΣΦ | | Submit Request Answer Value Request Answer vec Determine the displacement at point B measured downward. Use the method of virtual work. Express your answer to three significant figures and include the appropriate units. Enter positive value if the displacement is downward and negative value if the displacement is upward. < Return to Assignment Units → Provide Feedback ? ? rad Review

Consider the beam shown in (Eigure 1). Assume the support at A is a pin and C is a roller. Take E = 200 GPa. I = 150(106) mm¹. Suppose that w 17 kN/m. Figure < 1 of 1 > ..-(#) # 1.0 M Submit ✓ Part B Correct OB = Determine the slope at point B measured clockwise from the positive axis. Use the method of virtual work. Express your answer using three significant figures. Submit Part C Previous Answers AB= IVE ΑΣΦ | | Submit Request Answer Value Request Answer vec Determine the displacement at point B measured downward. Use the method of virtual work. Express your answer to three significant figures and include the appropriate units. Enter positive value if the displacement is downward and negative value if the displacement is upward. < Return to Assignment Units → Provide Feedback ? ? rad Review

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What are the possible Geometric Design? Make a table Containing the Geometric Design and Design Standard.
Compare and contrast the types of graphic representtaion. (Artistic Drawing and Industrial Technical Drawing)
What are the three-dimensional models used by BIM?
1. Please find the centroid and area of a quarter circle (refer Figure 1.0 below), user need to insert required parameter such as r. B- C
A finished sketch is also known as a: Group of answer choices Diagram Model Tracing Blueprint
A MarketV X bg Isaac Fra X com/course.html?courseld=172779808OpenVellumHMAC=83742633e6e9579bef30313512e3229e#10001 身口 M Review Part A A paper tube is formed by rolling a cardboard strip in a spiral and then gluing the edges together as shown in (Figure 1). The paper is 1.0 mm thick and the tube has an outer diameter of 100 mm. Determine the shear stress acting along the seam, which is at 50° from the horizontal, when the tube is subjected to an axial compressive force of 200 N. Express your answer to three significant figures and include appropriate units. HA Tz'y = Value Units Submit Request Answer Figure 1 of 1 < Return to Assignment Provide Feedback 40° 200 N 200 N 100 mm P Pearson 11:05 F Copyright © 2022 Pearson Education Inc. All rights reserved. | Terms of Use | Privacy Policy I Permissions | Contact Us | 5/5/20 58°F Mostly cloudy
Explain The application of AUTO CAD