Consider an ideal Brayton cycle using air as the working fluid, operating with a pressure ratio of 17. Air at 50 kg/s enters the compressor at 150 kPa and 700 K. The air then enters the turbine at 3000 K. Assume gas constant and specific heats at room temperature. Apply the ideal gas equation of state and isentropic relationships of ideal gas appropriately. (а) Analyse all pressures and temperatures in the cycle Using values of Qin» Żout and Wnet in MW, determine the thermal efficiency of the суcle. (b) (c) Illustrate proper P - v and T – s diagrams for the cycle, indicating all pressures and temperatures obtained in (a).

Consider an ideal Brayton cycle using air as the working fluid, operating with a pressure ratio of 17. Air at 50 kg/s enters the compressor at 150 kPa and 700 K. The air then enters the turbine at 3000 K. Assume gas constant and specific heats at room temperature. Apply the ideal gas equation of state and isentropic relationships of ideal gas appropriately. (а) Analyse all pressures and temperatures in the cycle Using values of Qin» Żout and Wnet in MW, determine the thermal efficiency of the суcle. (b) (c) Illustrate proper P - v and T – s diagrams for the cycle, indicating all pressures and temperatures obtained in (a).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

MODIFIED NON-IDEAL BRAYTON CYCLE GAS TURBINE: Use Air Standard Analysis SHOW COMPLETE SOLUTION.
Thermodynamics problem
3. A stationary power plant operating on ideal Brayton cycle has pressure ratio of 8. The gas temperature is 300 K at the compressor inlet and 1300 K at the turbine inlet. Utilizing the air standard assumptions, determine (i) gas temperature at the exit of compressor and turbine (ii) work ratio (iii) thermal efficiency.
A newly purchased sedan car operates on an ideal thermodynamic cycle. The engine has acompression ratio of 10. The ambient air pressure is 1 bar while temperature is 21 ºC. Themaximum temperature in the engine is 1600 K. Draw the ideal power cycle and label it.Utilizing the air-standard assumptions, determine (a) the gas temperature at the exits of thecompression and the expansion processes, (b) the specific works of compression, expansionand net, (c) heat supplied to the engine and (d) the thermal efficiency.
3. In a gas turbine plant air is compressed from 1.01 bar and 15 °C through a pressure ratio of 5. It is then heated in a combustion chamber at constant pressure to a temperature of 700 °C and expanded to atmospheric pressure in a turbine. The isentropic efficiencies of compression and expansion are respectively 0.8 and 0.85. Calculate (a) the cycle efficiency and (b) the work ratio. Assume that the properties of air do not change with temperature and may be taken as Cp = 1.005 kJ/kg K and y = 1.4.
Calculate the efficiency of the Carnot Engine for ideal gas. Consider the figure below for a complete cycle of Carnot engine, where the cycle goes from ad->ab->bc->cd
A 150 MW gas turbine power plant running on Ideal Brayton cycle has the following initial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature at the turbine is 910°C. Draw the P-V and T-S diagrams and determine the following: d. Thermal Efficiency e. Mass flow rate, kg/min
! Required information Problem 09.034 - Ideal Otto Cycle with Variable Specific Heats - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 95 kPa and 27°C, and 760 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Take into account the variation of specific heats with temperature. The gas constant of air is R = 0.287 kJ/kg-K. Problem 09.034.a - State After Heat Addition in Variable Heat Capacity Ideal Otto Cycle Determine the pressure and temperature at the end of the heat-addition process. (You must provide an answer before moving on to the next part.) The pressure at the end of the heat-addition process is 3915.8 kPa. The temperature at the end of the heat-addition process is 1647.7 K.
I need the answer as soon as possible
In a Rankine Cycle, real work produced by the turbine is less that the isentropic work. True False
With given,find,figure,analysis, and interpretation