Consider a tube having a rectangular cross-section as shown below. The tube is subject to two twisting moments of 70 Nm and 35N m. Determine the average shear stress developed at point 4 The tube is fixed at the other end.

Q: When an axial load is applied to the ends of the bar shown in the figure, the total elongation of…

A: Given Data  Total elongation of bar between A and C = 0.22 in  Normal strain in segment-2 = 1900…

Q: ) Write the equation for the neutral axis in the cross-section. b) Draw the normal stress…

A:

Q: The solid compound shaft made of three different materials carries the two torques as shown. (a)…

A:

Q: A plate with a 1.5-cm diameter circular hole is exerted with the bending moment M = 40 N-m. The…

A: Given bending moment , M = 40 Nm Sy = 400 MPa width of plate, b =3-dia of hole =(3-1.5)cm depth, d =…

Q: Consider the nonprismatic cantilever beam of circular cross section shown. The beam has an internal…

A:

Q: 1.) Solve the bending stress about poin and B 200kN m

A:

Q: 5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C,…

A: Given Data  Shear modulus (G) = 85 GPa  Diameter of shaft (d) = 40mm  Length of AB (LAB) = 0.5m =…

Q: Figure Q3 (a) shows an overhanging beam ABC subjected to a uniformly distributed load w along AB and…

A: yield stress of the material is 250 MPa

Q: The force p is applied at d=50 mm from the bottom as shown in the figure. Compute the normal stress…

A:

Q: The following shaft consists of a 3.50 m long steel shaft and a 2.00 m long aluminum tube. The steel…

A:

Q: In the figure, forces with resultant intensity Fx = 3P (unit N), Fy = 2P (unit N) and Fz = P (unit…

A: the largest P value according to the Von Mises assumption for the cube to be safe = 20a23explanation…

Q: Q3) The aluminum tube shown in Figure (2) has a thickness of (5 mm) and outer cross sectional…

A: For equilibrium  280 = 135 + Tc Tc = 145 Nm Average shear stress τ=T2tAmMaxm τavg will be obtained @…

Q: 2. Determine the shearing stress in each of the four walls of a portion of a structural aluminum…

A: Given, Torque =3 kN-m=26.55 kip-in Dimension=100×51 mm=3.93×2 in Wall thickness=4 mm=0.15 in.

Q: Problem Sets - 1: The thin-walled tube is used as a beam to support the uniformly distributed load…

A:

Q: 2. A thin-walled steel tube has an outer diameter of 100mm and a material thickness of Smm. The…

A: Given Data Do=100mm,  tm=5mm, Fs=2, δu=250Mpa, δu'=520 Now inter-Diameter Di=100-5=95mm Now, by…

Q: (2) A square member (400mm x 400mm) sustains an internal shear force of 150 kN and an internal…

A: Given: A square cross section of 400mm × 400mm Shear force = 150KN Bending moment = 250KN-m…

Q: The following shaft has a diameter of 60 mm, and it is made of Aluminum (G = 29 GPa). The shear…

A: Given, d=60 mmG=29 GPaτ= 200 MPaFOS=2.5ϕ=3 degree

Q: An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft…

A:

Q: For the state of plane stress shown below. 74. Determine the largest value of σy for which the…

A:

Q: e pins are 1 cm in diameter and are made of 304 stainless steel. A distributed load of 200 N/m is…

A: Given:- two rigid bars with a 5cm x 5cm section A-36 steel. the pins are 1 cm in diameter a 304…

Q: The plastic hexagonal tube shown in Figure (3), is subjected to a torque of 150 N. m. Determine the…

A:

Q: A solid shaft with diameter D mm and L mm long is supported between two bearings at the ends as…

A: "Since you have posted a question with multiple sub-parts. We will solve the first three sub-parts…

Q: The rigid beam AB is loaded with two forces each 31 kN and the 30-mm-in-diameter and…

A: Given:- P=31kNd=20mmL=1.25mDC=3.881mTo find:-Angle in rad by which rigid beam AB will rotate

Q: A 20mm diameter steel wire 150m long, is suspended vertically from one end. It supports a tensible…

A: The diameter of the wire is d=20 mm. The length of the wire is l=150 m. The load is P=20 kN. The…

Q: A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the…

A: We will find shear area and multiply with stress.

Q: The solid steel rod (1) shown in the figure has an allowable shear stress of 3 ksi. The brass tube…

A:

Q: ABC carrying a pure moment of M kN.m at point B. The cross-sectional area of the beam is shown in…

A:

Q: The thin-walled tube is used as a beam to support the uniformly distributed load of intensity wo as…

A: For the given beam and cross-section,  the maximum load w0 for allowable bending stress of 1000…

Q: A two-bar system has the configuration shown in the Figure Q1 below. The cross-sectional area for…

A:

Q: ress at point A is ress at point Bis [ ksi. ksi.

A:

Q: The solid steel rod (1) shown in the figure has an allowable shear stress of 18 ksi. The brass tube…

A: Given : Allowable shear stress of brass tube = 6 ksi Allowable shear stress of solid steel rod = 18…

Pressure and Stress