Configuring Inter-VLAN Routing. Legacy inter-VLAN routing (or per-interface inter- VLAN routing) requires multiple physical interfaces between the router and the switch. The switch interfaces are set to access mode and assigned one VLAN. The router needs nothing special to route the VLAN traffic other than addressing for the VLAN's subnet. Because this is legacy inter-VLAN routing, we will not review it any further. You just need to be aware of what it is and how it is configured. An alternative in larger networks is to use VLAN trunking and subinterfaces. VLAN trunking allows a single physical router interface to route traffic for multiple VLANS. This technique is termed router on a stick and uses virtual subinterfaces on the router to overcome the hardware limitations based on physical router interfaces. a. List the commands including command syntax and prompt to configure a router for router-on-a-stick inter-VLAN routing. b. List the commands including syntax and prompt to configure a switch to support inter-VLAN routing. c. What commands cannot be used on the router? Why?

Q: We are aware that TCP's transport layer manages end-to-end error management. Theoretically, error…

A: Network communication involves the transmission of data over various layers of the network stack,…

Q: What exactly does the word "route aggregation" mean? What is the benefit of a router performing…

A: Solution : Route Aggregation Route aggregation is a technique for condensing several individual…

Q: Because Ethernet is a distributed local area network protocol, there is no centralised control node;…

A: A distributed system consists of different autonomous node groups that collaborate to accomplish a…

Q: a) What advantage does a circuit-switched network have over a packet-switched network? What…

A: Answer to the given question: Answer(1): Advantage of circuit switch network over a packet switched…

Q: What is the primary function of a router in the context of the OSI model? Can you name another…

A: In the OSI model, routers play a role in the Network Layer (Layer 3).Their main aim is to ease the…

Q: Explain the function of each kind of router that may be found in an interconnect network in a few…

A: A network is a collection of computers, servers, mainframes, networking equipment, peripherals, and…

Q: What is the primary purpose of a router in the OSI model, and which layer of the model does it…

A: The primary purpose of a router in the OSI (Open Systems Interconnection) model is to enable the…

Q: We made a distinction between the forwarding function and the routing function performed in the…

A:

Q: In contrast to datagram and virtual-circuit networks, circuit-switched networks don't need a routing…

A: We said that two kinds of networks, datagram, and virtual circuit, need a routing or switching table…

Q: When it comes to mobility, what are the distinctions between session location and dynamic-routing?

A: Dynаmiс  rоuting: Dynаmic routing, also known as adaptive routing, is when a router uses the current…

Q: Explain the role of Multiprotocol Label Switching (MPLS) in WANs. What benefits does it offer…

A: Multiprotocol Label Switching (MPLS) is a crucial technology in Wide Area Networks (WANs) that…

Q: e us

A: Given   Both Layer-2 switches and routers are used to route network data between interfaces. How…

Q: What is meant by a control plane that is based on per- router control? In such cases, when we say…

A:

Q: What is the difference between the OSI levels if routers occupy many layers?

A: In response to your query, The Open Systems Interconnection Model (OSI Model) is a conceptual…

Q: Does the purpose of internal network routing protocols vary from that of external network routing…

A: the internal routing of a network The process of choosing a route for traffic inside a network or…

Q: a) What method can be used by two computers to ensure that packets are not dropped because too much…

A: #include <stdio.h> int main() { int n1, n2; printf("Enter two positive integers:…

Q: Transport Control Protocol (TCP) is a transport layer protocol that provides full-duplex,…

A: TCP is a transport layer protocol that delivers full duplex, connection-oriented, and dependable…

Q: router

A: A router is a crucial networking equipment, located at the Network Layer (Layer 3 of the OSI model).…

Q: Q: Describe in detail how TCP packets flow in the case of TCP handoff, along with the information on…

A:

Q: The path of a packet is defined by source and destination addresses in a connectionless system like…

A: Introduction: A connectionless protocol is one that allows two network endpoints to communicate…

Q: Given the following diagram. S1, S2, and S3 are layer-2 switches. R1 and R2 are network layer…

A: As per our company guidelines only three sub parts will be answered. First question contains 4…

Q: Design an implementable routing and bridging solution for the network. Ensure that the solution…

A: According to the information given:- We have to design an implementable routing and bridging…

Q: (a)  What different switching mechanisms exist to forward datagrams from an input port to an output…

A: a) There are 3 switching mechanisms that exist Circuit switching - creates a virtual network Packet…

Q: What is the primary purpose of a router in the context of the OSI model? How does it operate at the…

A: In the OSI model, which is a framework used to understand how various networking protocols work…

Q: What is meant by a control plane that is based on per- router control? In such cases, when we say…

A: What is meant by a control plane that is based on per router control? In such cases, when we say the…

Q: We are aware that TCP handles end-to-end error handling at the transport layer. Theoretically, error…

A: TCP: TCP (Transmission Control Protocol) is a communication protocol that links various networking…

Q: What are the differences between the various sliding window protocols used in the data connection…

A: Introduction: Sliding Window Protocol: The sliding window is a technique for sending multiple frames…

Q: Distinguish between infrastructure based and infrastructure-less routing

A: Distinguish between infrastructure based and infrastructure-less routing

Q: I'm curious as to when a network administrator might want to employ a static routing configuration.

A: Introduction: Static routing may be used to establish an exit point from a router when no other…

Q: The Ethernet is a distributed LAN protocol, meaning that no centralized control node is available…

A: Centralized LAN protocol

Q: We are aware that TCP's transport layer performs end-to-end error handling. Theoretically, error…

A: TCP stands for Transmission control protocol which is Transport layer protocol. This is a connection…

Q: We are aware that TCP's transport layer takes care of handling errors at both ends of a connection.…

A: According to the information given:- We have to define TCP's transport layer takes care of handling…

Q: What are the distinctions between the various layers of the OSI model when routers are present at…

A: The OSI (Open et al.) model a conceptual framework to understand how different network protocols…

Q: What is the primary function of a router in the OSI model, and which layer does it operate at?

A: The OSI model is a framework that provides a way to organize network protocols and communication…

Q: What is meant by a control plane that is based on per- router control? In such cases, when we say…

A: The control plane that is based on per router control. We say the network control and data planes…

Q: What is meant by a router control? In s control and data pla

A: Summary Control plane  The control plane is a set of services within the network that perform…

Q: IP is a Routed Protocol, just like ICMP and IGMP: whereas RIP, OSPF, BGP are all Routing Protocols,

A: ANSWER: IP(Internet Protocol): IP means "Internet Protocol," which is the arrangement of rules…

Q: Differences between dynamic-routing and session location mobility may be explained as follows:

A: Introduction: process in which a rоuter may forward data through an alternative route or to a…

Q: Communication between routers on the per-router control plane (or classical network) is accomplished…

A: SDN stands for Software-Defined Networking. SDN is a networking approach that uses separates the…