Compute the critical load in kN, corrected to one decimal place.

Q: The efficiency of a power screw does nột depend on which of the following variables. Hint: Look at…

A: formula for efficiency of power screw is given byη=Fl2πThere F=load in newtonl=lead T=torquetorque…

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A:

Q: 0.7500 t.0008 1.1808 1.1800 Calculate the diameter limits for the shaft, 'ØW', to have a total…

A:

Q: The shaft shown in the Figure is driven by 3 KW motor. It transmits the power through the sprocket…

A: In this problem, we have to draw the loading diagram of the given diagram.

Q: A steel beam, of lengths a=5 m and b= 2 m and a hollow box cross section, is supported by a hinge…

A: Here reaction force along x-direction at pin support A is neglected as there are no applied force…

Q: For the stress element below, when a = 6, b = 4, and c = 6, the principal stress σ1 , the largest…

A:

Q: Given: V = 60 fps, u = 25 fps, ß = 120°. Determine V, in fps. Select one: O a. 31.3 O b. 29.3 O c.…

A: Given data: absolute velocityV=60 fpsvelocity of the bladeu=25 fpsangleβ=120°   Find out: The…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Compute the lead angle of M16 x 1.2 thread

A:

Q: reciprocating saw needs to move the blade downward 0.75 in in 0.10 s anc turn in 0.08 s. Determine…

A: As per company's guidelines we can answer only 1st question

Q: A=pi r^2, you forgot to divide the diameter by 2 before plugging it in

A:

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: Express the quantity 556.2 x 10^-12s in fs.

A: Given Data: The time given is t = 556.2×10-12 s. The conversion of second to femtosecond can be…

Q: Q2/ Determine the diameter of the rivets and the forces in all rivets. Take Tallowable as 60 MN/mm2.

A:

Q: Draw SF and BM diagrams for the shaft below. 2 kN/m B 600 mm 450 mm 300 mm

A:

Q: Determine the relative roughness of cast iron pipe with inner diameter 3.1 inches. Your answer…

A: Given Internal Diameter (D) = 3.1 inches                                    = 3.1 * 25.4 mm…

Q: Tapered gibs are adjusted by screws spaced out along the length of the gib. Select one: O True O…

A: Tapered gibs

Q: Find the depth of thread in mm for an external thread, if the pitch is 5 mm. Depth of thread (in mm)…

A: Given : Pitch (p) = 5mm   To find : Depth of thread (d) =?

Q: Shear stress has units:

A: The units of shear stress are like the units of any other type of stress. The unit for shear stress…

Q: I have a pin with a Diameter of 10.00/9.95. What is the Maximum Bow of this pin?

A: bow in pin:-

Q: he block brake, as shown in the figure, provides a braking torque of 376 N-m. The diameter of the…

A:

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm²…

Q: 8. The stress in a pipe varies jointly with the internal pressure and the diameter of the and…

A: Define variables. σ=the stress in pipe(pounds/in2)P=the internal pressure of the pipe…

Q: -0.0025 1. The dimensions for the shaft size are o50-0.0037 mm and the hole size are +0.000 mm. Find…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: Match M, V, or N to the correct definition could have units kN-m bending moment 1. M perpendicular…

A: In the above question there are three variables M, V, and N. Here, M symbol used to represent the…

Q: Compute for the value of the uniformity coefficient with the data shown below. D10 = 0.08 mm…

A: UNIFORMITY CO-EFFICIENT: It is defined as the ratio of size of opening that will just pass 60% of…

Q: A spherical tank for storing gas under a pressure is 20 m in diameter and is made of steel 20 mm…

A:

Q: Two gray cast iron plates, each with a thickness of 1.75 inches are compressed together with a 1.000…

A:

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

A:

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: For the truss in figure below, the cross-sectional area of the truss members isA = 500 mm²…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. A = 3.55 B…

A:

Q: Question 15 A solid cylindrical shaft which has a diameter of 63 mm and is 1 metre long, experiences…

A:

Q: 50 +0.012 mm and the hole size are 1. The dimensions for the shaft size are +0.015 50+0.005 +0.000…

A:

Q: An cylinder has a volume of 38.5 cu.in. and clearance of 2.5 cu.in. Calculate the stroke, if the…

A: Given data:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.