A car weighing 4000 lb, with a wheel base of 9 ft, carries 1500 lb of its load on the front wheels. Compute themaximum shear in lb when crossing a 14-ft span. ide the unit of your answer.DO NOT COPY the answer of your classmates since the exam that was prepared for you generates 200 set.DISTINCT problem to solve.uck and God Bless.Question 2A car weighing 4000 lb, with a wheel base of 9 ft, carries 1500 lb of its load on the front wheels. Compute themaximum shear in Ib when crossing a 14-ft span.Next >- PreviousSubmit QuizNot saved

Answered: Image /qna-images/answer/db3876f1-31d4-44dd-aa32-eac7779b71ad.jpg

Answered: car weighing 4000 lb, with a wheel base…

car weighing 4000 lb, with a wheel base of 9 ft, carries 1500 lb of its load on the front wheels. Compute the maximum shear in lb when crossing a 14-ft span.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: m, 3 m an

Q: Situation 3- A horizontal prismatic beam with span of 3 meters is fixed at the left end and free at…

A: Given data,cantilever beam FINDa)what is deflection at free end if the concentrated load was acting…

Q: A propped cantilever made of a prismatic steel beam is subjected to a concentrated load P at mid…

Q: A 12m simply supported beam is cambered up by a compressive force acting on its cross-section. The…

A: Given P=1200kN w=10kn/m L=12m e=150mm W=?

Q: A steel beam is made up of a wide flange section whose total depth is 600mm, width of the flange is…

A: Please refer and use given formula in above question M =wL28 + PL4 M = 40 × 928 + 200 × 94 M = 855…

Q: A simple supported beam made up of steel with a maximum shear resistance of 150 MPa is subjected to…

Q: Q.I A truck with axle loads of 45 kN, 60 kN and 30 kN separated by 4 and 6 m respectively. If this…

A: Solution Diagram of loading

Q: 270 lb/ft Where is the point of zero shear located from support A? а. 5.0 m b. 4.5 m A B с. 4.0 m d.…

Q: In the given loaded beam determine the resultant force, R and its location from the point show…

A: To determine the resultant and the location of the resultant. The magnitude of the resultant can…

Q: Design a sliding gate wing type of beams (w8*40) which have an elastic section modulus equal to 582…

Q: Four wheel loads rolls as a unit across a 16- m span. The loads are 40 kN, 30 kN, 20 kN, and 10 kN…

Q: A car weighing 3000 lb, with a wheel base of 9 ft, carries 1200 lb of its load on the front wheels.…

A: For the given car,

Q: B. A truck with axle loads of 30 kN and 500 kN on a wheel base of 4 m rolls across a 8-m span.…

Q: A car weighing 3000 tb, with a wheei base of 9 ft, carries 1100 b of its load on the front wheels.…

Q: 3. A continuous beam bridge with a structural importance coefficient of 1.1. The mid span bending…

A: GIVEN Mid span Bending Moment due to self weight , MD=500 KN-m Mid span Bending Moment due to…

Q: A load of 100 kN, followed by another load of 50 kN, at a distance of 10 meters, advances across a…

A: We have to determine the value of expression for the maximum bending moment at a section of the…

Q: A truck and a trailer combination whose axle loads are indicated as shown is to cross a 14-meter…

Q: a). What is the minimum diamétér of a solid 6m stéél shaft that will carry a shearing stress of not…

Q: truck with an axle load of 30kn and 70kn on the wheel base of 5m rolls across a 12 span. Compute the…

Q: For questions 1A, 1B, and 1C. The figure below shows the reinforced concrete beam AB of a tourist…

A: Given data: Load=2500 N/m It is asked to find maximum shear force and Bending moment.

Q: standard HS truck is moving across a 25-m simple span. The wheel loads are Pa= 36 kN, Pb = 142 kN,…

Q: A bus with axle load of 40kN and 60kN on a wheel base of 5m rolls across a 10m span. Compute the…

A: Maximum bending moment - bending moment under the load will be maximum when the load and resultant…

Q: If it is known that the column is part of the unswayed frame structure and has a single curvature…

A: To check whether the reinforced concrete column is capable of carrying the ultimate factored load,…

Q: Determine the Vmax and Mmax. Draw the shear and moment diagram of the loaded beam shown in the…

Q: 1. A 80-ft simply supported beam is subjected to a three wheel moving load. The loads, shown in the…

A: We use Muller Breslau principle to determine the ILD for maximum shear (at the supports). To…

Q: The beam shown below is a cross section of a beam for a 4-storey commercial building. Due to limited…

A: Area of steel below neutral axis (As) = 3 x 1/4π(d)2 = 3 x 0.785 x( 16)2 = 602.88mm2…

Q: A car weighing 4000 lb, with a wheel base of 9 ft, carries 1500 lb of its load on the front wheels.…

Q: Q1) A uniform T-section beam is 50 mm wide and 100 mm deep with a flange thickness of 25mm and a web…

A: Question is based on the T beam subjected to uniformly varying load . Magnitude of load , dimension…

Q: A floor system supporting a 6 in. concrete slab is shown in Figure P11.4. The live load is 100 psf.…

A: LL=100 lbft2Thickness of slab=6 inchesγc=150 lbft3A992 steel is used for both beams and girdersTo…

Q: A 7-meter simple beam has one of its supports at the left end and the other is placed 3m from the…

Q: A car weighing 2000 lb, with a wheel base of 9 ft, carries 1300 lb of its load on the front wheels.…

Q: Four wheel loads rolls as a unit across a 19-m span. The loads are 50 kN, 40 kN, 30 kN, and 10 kN…

Q: A truck with axle loads of 30 kN and 60 kN on a wheel base of 4 m rolls across a 10-m span. Compute…

Q: A car weighing a 2000 lb, with a wheel base of 9 ft, varries 1400 lb of its load on the front…

A: Draw ILD

Q: A car weighing 4000 lb, with a wheel base of 9 ft. carries 1600 lb of its load on the front wheels.…

Q: A truck with axle loads shown rolls across a 10-m span. What is the maximum bending moment and…

A: For the given rolling loads across a 10m span, the maximum shear and bending moment have to be…

Q: and trailer cO le is 4 kips, the

Q: An existing beam shown carries an 8-ft high wall. It will be renovated and be replaced with the ff…

A: To find:The load that the beam will carry in kN/m

Q: In beam test what is the advantage of a third point loading instead of using a single load in the…

A: Please refer the attached image for complete solution.

Q: A prefabricated wood I-beam serving as a floor joist has the cross section shown in the figure. Z…

A: Given, Allowable shear load = fallow = 77lb/in Height of web= 7in. Width of the flange = b= 5in.…

Q: A simple beam 20 ft in length has a concentrated load of 8000 lb at the center of the span. Compute…

Q: A truck with axle loads of 20 kN and 60 kN on a wheel base of 6 m rolls across a 14-m span. Compute…

A: Given data, Truck axle load = 20 kN and 60 kN Wheel base = 6 m Span = 14 m To find out the…

Q: car weighing 2000 lb, with a wheel base of 9 ft, carries 1400 lb of its load on the front wheels.…

Q: Q4 A single rolling load of 20 kN rolls along a girder of 25 m span. Draw the diagrams of maximum…

Q: A car weighing 4000 lb, with a wheel base of 9 ft, carries 1400 lb of its load on the front wheels.…

Q: A truck with axle loads shown rolls across a 10-m span. Compute the maximum bending moment and…

A: l = 10m P1 = 20KN P2 = 10KN P3 = 40KN

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

A car weighing 4000 lb, with a wheel base of 9 ft, carries 1500 lb of its load on the front wheels. Compute the maximum shear in lb when crossing a 14-ft span.

ide the unit of your answer.
DO NOT COPY the answer of your classmates since the exam that was prepared for you generates 200 set.
DISTINCT problem to solve.
uck and God Bless.
Question 2
A car weighing 4000 lb, with a wheel base of 9 ft, carries 1500 lb of its load on the front wheels. Compute the
maximum shear in Ib when crossing a 14-ft span.
Next >
- Previous
Submit Quiz
Not saved

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simple supported beam made up of steel with a maximum shear resistance of 150MPa is subjected to a self-weight of 88N/mm. In addition to the self-weight, the beam is also subjected to point loads acting at the beam mid-span . Find out the magnitude of point load acting on the beam such that the shear stresses does not exceed the allowable shear stresses. The beam has a I-shape cross section having flanges dimensions of 300mm wide and 8mm thick and web with a thickness of 8mm and height of 284mm. The span length of the beam is 4 m. Consider the self weight of the beam in solving the question.
Strength of materials The answer should be – 96 per cent of shearing force carried by web; 88 per cent of bending moment carried by flanges.
The reinforced concrete column shown in Figure 3 is made with 5000 psi concrete and reinforced with Grade 60 steel. What is the maximum axial force ?? the column can safely support?
Four wheel loads rolls as a unit across a 18 span. The loads are 50kn, 30kn, 20kn and 10kn separated respectively by distances of 1m, 3m and 6m. Compute the maximum shear in kn
A car weighing 3000 lb, with a wheel base of 9 ft, carries 1500 lb of its load on the front wheels. Compute the maximum shear in lb when crossing a 14-ft span.
12. Determine the reactions R₁, R₂, R3, and R4 using Three Moment Equation. Provide free body diagram of the spans. R₁ 100 lb/ft 10 ft R₂ 5 ft -160 lb/ft 400 lb R₂ 5 ft 3 ft- MATHaling.co 400 lb 6 ft 3 ft R4
A straight cantilever of uniform cross-section carries a total load W distributed evenly over its entire length. If the free end of the cantilever is now propped upto the level of the fixed end, the vertical force required at the prop is
A steel beam 12m long is fixed at both ends and carries a superimposed uniformly distributed load of 35kN/m. The beam is W18x46 whose relevant properties are shown below. Properties: Flange width bf=153.9mm Flange thickness tf = 15.4mm Overall depth d= 458.7 Web thickness tw- 9.1mm Beam weight = 68.5kg/m Moment of inertia = 296, 357x10 ³mm4 Which of the following most nearly gives the maximum bending stress in the beam? Select the correct response: 165.56Mpa 331.27Mpa 231.27Mpa 185.56Mpa
Pls answer asap. Use 4 decimal places