A reinforced concrete circular pile of 12 m length and 0.6 mdiameter is embedded in stiff clay which has an undrainedunit of cohesion of 110 KN/m². The adhesion factor is 0.5.Calculate the Ultimate pull out load for the pile.

Given data, A reinforced concrete circular pile of, Length,l= 12 m Diameter,d= 0.6 mUnit of…

Answered: Calculate the Ultimate pull out load…

Engineering

Civil Engineering

Calculate the Ultimate pull out load for the pile.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.12P

See similar textbooks

Similar questions

A reinforced concrete circular pile of 12 m length and 0.6 m diameter is embedded in stiff clay which has an undrained unit of cohesion of 110 KN/m². The adhesion factor is 0.5. Calculate the Ultimate pull out load for the pile.
Evaluate the resisting capacity against axial load due skin friction of a concrete pile embedded into a layer of plastic clay given in the following conditions: Size of pile = 0.4 m square Depth of penetratian inta the clay layer = 40 m Unconfined compression strength (qu) af the clay = 200 KPa Ans. 6400 kN
A concrete pile 458 mm by 458mm square cross section is embedded in a saturated clay. The length of the embedment is 16 m. The undrained cohesion, Cu of clay is 60 kN/m2, and the unit weight of clay is 18 kN/m2. Use a factor of safety of 5 to determine the allowable load the pile can carry
A nine pile group consists of 0.30m diameter friction concrete piles 12m long. The piles are driven into clay having an unconfined compressive strength of 180kPa and the unit weight of clay is 18kN/m3. The spacing of piles is 0.75m center to center. Assuming a bearing capacity factor of Nc = 9, a= 1.0. Which of the following most nearly gives the minimum pile spacing in order to achieve 100% efficiency?
A square group of 25 piles extends between depths of 2 m and 12 m in a deposit of 20 m thick stiff clay overlying rock. The piles are 0.5 m in diameter and are spaced at 1 m centre to centre in the group. The undrained shear strength of the clay at the pile base level is 180 kPa and the average value of the undrained shear strength over the depth of the pile is 110 kPa. The adhesion coefficient (a) is 0.45, FOS against shear failure is 3. Take No= 9. %3D When pile acting in a group Q,, Capacity of pile group
A reinforced concrete circular pile of 12 m length and 0.6 m diameter is embedded in stiff clay which has an undrained unit cohesion of 110 kN/m². The adhesion factor is 0.5. The net Ultimate Pullout (uplift) Load for the pile (in kN, round off to 1 decimal place) is
A square precast concrete pile of sides 0.40 m is to be driven 12 m into the soil strata as shown. Determine the frictional resistance of the pile using β method. Assume β = 0.265
A precast concrete pile of size 50 cm x 50 cm is to be driven into clay strata whose unconfined compressive strength is 220 kN/m2 and adhesion factor = 0.6. The length of the pile required to carry safe working load of 450 kN with factor of safety of 2.5 is
A square concrete pile of 10 m length is driven into a deep layer of uniform homogeneous clay. The average unconfined compressive strength of the clay, determined through laboratory tests on undisturbed samples extracted from the clay layer, is 100 kPa. If the ultimate compressive load capacity of the driven pile is 632 kN, the required width of the pile is mm. (in integer) (Bearing capacity factor Nc = 9; adhesion factor a = 0.7)
(i) What are the components of elastic settlement of piles? Name two parameters that affect the settlement. A 300 mm diameter pile penetrates a deep deposit of soft clay 9 m deep. Compute the skin friction and point bearing capacity. The clay has an undrained unit cohesion of 60 kN/m?. Assume a (ii) constant friction coefficient of 0.75 and use a method.
A group of 16 piles of 10 m length and 0.5 m diameter is installed in a 10 m thick stiff clay layer underlain by rock. The pile-soil adhesion factor is 0.4; average shear strength of soil on the sides is 100 kPa; undrained shear strength of the soil at the base is also 100 kPa. 12.9 The base resistance of a single pile is (a) 40.00 kN (b) 88.35 kN (c) 100.00 kN (d) 176.71 kN
A group of nine piles 300 mm in diameter is driven into a clay layer 16 m thick with rock below the clay layer. The pile is 9 m long and spaced 500 mm centres. The clay has the following properties: - an undrained shear strength of 100 kN/m2, adhesion coefficient α=0.5, Eu =40 MN/m2 and mv = 0.09 m2/MN. The pore water coefficient A= 0.38. The dead load carried by the pile group is 2300 kN and the live load is 500 kN. Verify if the ultimate and serviceability limit states for an allowable settlement of 30 mm are satisfied.