Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal assembly. Each traffic signal has a mass of 42 kg, while the masses of members OC and AC are 79 kg and 73 kg, respectively. Positive answers are to the right, up, and counterclockwise. A 42 kg 6.5 m 42 kg B G 1.0 m 73 kg 5.5 m 79 kg C 0 6.9 m

Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal assembly. Each traffic signal has a mass of 42 kg, while the masses of members OC and AC are 79 kg and 73 kg, respectively. Positive answers are to the right, up, and counterclockwise. A 42 kg 6.5 m 42 kg B G 1.0 m 73 kg 5.5 m 79 kg C 0 6.9 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8z The value of when z = 2. = -1 is Select one: of stion O - 12 O 3 O-6 PREVIOUS PAGE NEXT PAGE
Please Asap
(b)show that: I(cosh at cos at) s++4a*
I need an answer quickly please.
Choice the correct answer of the following statements: 1. The power transmitted of two pulleys connected by an open belt or crossed belt is a) directly proportional to their diameters; b) inversely proportional to their diameters; proportional to the square of their diameters; c) directly d) inversely proportional to the square of their diameters. 2. Two pulleys of diameters d1 and d2 and at distance x apart are connected by means of an open belt drive. The length of the belt is: a) π/2 (d: + d₂) 2x + (d: + dz)/4x; b) n/2 (d₁-dz) 2x + (di-dz)/4x; c) n/2 (d: +d₂) 2x + (di-d₂}/4x; d) π/2 (d₁-də) 2x + (d: +d₂)²/4x. 3. In a cone pulley, if the sum of radii of the pulleys on the driving and driven shafts is constant, then: a) open belt drive is recommended; b) cross belt drive is recommended; c) both open belt drive and cross belt drive are recommended; d) the drive is recommended depending upon the torque transmitted. 4. Due to not slip of the belt, the power transmitted of the belt drive:…
kindly answer it
3. Column ABC has a uniform rectangular cross-section and is braced in the xz plane at its midpoint C is shown Figure Q3(a). Given, the factor of safety is 2.7, P=5.4 kN, L=600 mm and E=70 GPa, determine the ratio b/d for which the factor of safety is the same with respect to buckling in the xz and yz planes
1 The basic drilling process is that a at the bottom of_ grinds a hole through the rock layers.
Q.7 Degree of freedom at triple point is A В D -1
The hollow tube rotates with an 01 = 5 rad/s and 2= 6 rad/s. The sphere A is moving along the shaft (away from the origin) with an = 5 m/s and = 4 m/s². Find the i, j, and k components of the velocity and acceleration of A at this instant if 9 = 35 degrees. Assume r = 6 m. VA = aA = î km/s (1 decimal) k m/s² (no decimals) j+ Ĵ+
(b) A plastic rod AB of length L = 510 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic sleeve CD of length c = 300 mm and outer diameter d2 = 45 mm is securely bonded to the rod so that no slippage can occur between the rod and the sleeve. The rod is made of an acrylic with modulus of elasticity E1 = 3.1GPA and the sleeve is made of a polyamide with E2 = 2.5GP . (i) Calculate the elongation & of the rod when it is pulled by axial forces P=15KN . (ii) If the sleeve is extended for the full length of the rod, what is the elongation? (iii) If the sleeve is removed, what is the elongation?
Question 28 Not yet an If a particle is projected vertically upwards, it travels against gravitational force and hence the velocity of the particle will go on decreasing and velocity becomes zero, when it reaches the maximum height. Select one: O True O False hp