Calculate the buckling loads using the Euler and Rankine approaches for a tubular steel strut, 3m long, which is fixed at both ends. The outside and inside diameters are 100 mm and 80 mm, respectively. What will be the factor of safety according to Rankine's formula if o = 245 MPa and the Rankine's constant is 1/6500.(E = 200GPa) %3D

Calculate the buckling loads using the Euler and Rankine approaches for a tubular steel strut, 3m long, which is fixed at both ends. The outside and inside diameters are 100 mm and 80 mm, respectively. What will be the factor of safety according to Rankine's formula if o = 245 MPa and the Rankine's constant is 1/6500.(E = 200GPa) %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

is strengthened by bolting two cover The wide-flange beam shown in Fig. plates 160 mm by 20 mm to the top and bottom flanges. If the maximum flexure stress is 140 MPa, compute the total force (a) in each cover plate and (b) in each flange. Neglect the weakening effect of the bolt holes. 160 mm 20 mm 20 mm 320 mm 20 mm €20 mm
Correct answer.
Determine the positive nominal flexural strength Mn of the T-beam in the figure below. Assume fc′ = 21MPa and fy = 420MPa Determine the effective width of the flange if the clear spacing of the beams is 2m while the clear span length of the beam is 3m. Determine the Nominal Moment Capacity of the beam considering that the diameter of stirrup is 10mm and the concrete cover is at 40mm.
Question Three The three-bar truss ABC shown in the figure part a has a span L = 3 m and is constructed of steel pipes having cross-sectional area A = 3900 mm² and modulus of elasticity E = 200 GPa. Identical loads P act both vertically and horizontally at joint C, as shown. (a) If P=475 kN, what is the horizontal displacement of joint B? (b) What is the maximum permissible load value Pmax if the displacement of joint B is limited to 1.5 mm? P A 45° 45° B L (a)
a.what is the maximum bending stress fbx (MPa) in the girder b.determine the maximum bending stress fby (MPa) in the girder c.using interaction formula fbx/Fbx + fby/Fby
FN= 119, MN= 85, SN= 93
Help
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa;1 = 370 x 106 mm“]. For the loading shown, determine the beam deflection vc at point C. %3D Assume P = 73 kN, w = 35 kN/m, LAB - LBC= 3.6 m, LCD= 1.7 m. %3! P. B |C D LAB LBC LCD Answer: Vc= 8.8767 mm.
3.6 m F A (1) 2.4 m Rigid bar B (2) E 1.8 m (3) C D X 3.0 m The assembly shown consists of a rigid bar ABC, two fiber-reinforced plastic (FRP) rods (1) and (3), and FRP post (2). The modulus of elasticity for the FRP is E = 16 GPa. Determine the vertical displacement of joint D relative to its initial position after the 34 kN load is applied to the nearest .1mm. A1 = 500 mm^2 A2 = 1,384 mm^2 A3 = 536 mm^3
Plz, solve this problem using Flexibility method and show all the steps one by one and draw SFD and BMD Structural Analysis-2
A built up I-section is formed from plates welded together as shown in the figure. It is to be used as a column L = 3.7 m long. All elements are A36 steel and connected such the section is fully effective. Using the following properties, calculate the flexural buckling stress, Fcr, in MPa using theoretical k. Flanges: b = 150 mm, tf = 12 mm Web: h = 310 mm, tw = 6 mm Write your final answer in two decimal places only.
Determine the maximum safe service live load that the beam can carry if the service dead load is 12 kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40 MPa and fy=415 MPa. Top bars are 6-32mm and bottom bars are 3-28 mm, center to center distance between the bar layers is 108mm. 70 mm 108 mm 352 mm 7.2 mm 6.7 mm B A 70 mm 300 mm