Box-section cantilever beam in the figure bears. Safety stresses in pressure and tension respectively σp,allowable= 100 MPa and σt,allowable = 120 MPa. a) Draw the bending moment diagram. b) Find the maximum load q that the beam can safely carry. c) (according to the load q determined in part b) normal in the section Plot the stress distribution. Note: Ignore the cutting effect in calculations.

Q: Figure Q6 shows the cantilevered 6061-T6 aluminum alloy rectangular beam fixed at A. Given Modulus…

A:

Q: Consider the beam shown in (Figure 1). Take w= 1.8 kip/ft. A) Determine the shear stress at point C…

A: Given:The uniformly distributed load is the length of AB is the thickness of the section is

Q: Two 160 mm * t cover plates are welded to two channels 200 mm high to form the cross section of the…

A:

Q: A bending moment of M=150 kips-in is applied at the cross section of beam shown in Figure Question…

A:

Q: A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress…

A:

Q: Design a timber glue-lam beam made from douglas fir for the given load in the figure below. 670…

A:

Q: Two uniformly distributed loads w = 4200 lb/ft of act on the simply supported beam shown in Figure…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A: The applied force is .The dimension are The allowable shear stress is

Q: a) Find the maximum normal stress and maximum shear stress. b) Compare these values with the…

A: We are to determine the shear stress  and normal bending stress for the beam For this we will…

Q: Two 160 mm*t cover plates are welded to two channels 200 mm high to form the cross section of the…

A:

Q: 3-A simply supported beam of length 4 m, is subjected to an Uniformly distributed load of 26 kN/m…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: (a) Determine the reaction forces at connections A and B. (b) Draw the shear force and bending…

A:

Q: igid support geomet in the figure and parameter table. Find the equations for the shear and moment…

A: Given: The length of AB, L1 = 4 m The length of BC, L2 = 4 m The length of CD, L3 = 3 m The moment…

Q: Example 4 The simply supported beam in Figure below has a rectangular 3kN cross section 100 mm wide…

A: Solution: To find support reactions at A and B, considering static equilibrium,…

Q: Two 160 mm * t cover plates are welded to two channels 200 mm high to form the cross section of the…

A: Given: The allowable bending stress, σ = 255 Mpa The moment of inertia, I = 2.06x106 mm4 the length…

Q: A beam made of Al 2014-T6 aluminum alloy is loaded by an oblique bending moment of M= 5 kN.m as…

A: Solution: a) Centroid of the cross-section y¯ can be calculated by, Let area A1 = 90×10=900mm2…

Q: beam at quarter of the

A: Given ,

Q: The simply supported beam AB as shown in Figure Q3(a) has a uniform load of intensity, w - 15 kN/m…

A: Given we have w=15 KN/mINA=3.6 X 106 mm4RA=RB (symmetric loading)⇒RA+RB=15(0.6+1.8)⇒ZRA=1.5 X…

Q: end pin supported beam has the cross-se

A:

Q: Uniformly distributed load on a simple support beam with a length of 6 meters Maximum that occurs on…

A: Given data: The length of the beam is l = 6 m. The bending stress of the beam is σ = 337.5 MPa. The…

Q: Q: For the loaded simply supported beam shown in figure below, if the allowable bending stress is…

A:

Q: wood with Your ed to a uniform stresses due to lied (indicating ti

A: Given that ,  Beam length L=3 m Young's modulus E=15 GPaRectangular cross section dimension , b=98…

Q: The steel beam in Figure A has the cross section shown in Figure B. The beam length is L = 6.0 m,…

A: The dimension are The length of beam is The maximum bending stress is

Q: A beam has the the geometry and dimensions shown in the figure and parameter table. If the allowable…

A: Given:The allowable shear stress, The intensity of the distributed load is

Q: A simply supported beam carrying floor joist shown in Figure 6.22 is made of rectangular wood having…

A: Given data: P=1 kN Need to determine the bending stress.

Q: on 5 Let's consider a fixed supported beam subjected to a triangular distributed load as shown in…

A:

Q: (a) Maximum tensile flexural stress (Indicate where it occurs what section and where in the…

A: Given that ,  w=5kN/mP=15.11kN

Q: For the loaded beam shown in Figure Q6 below, consider section M-M and determine the following: 6.1…

A: Solution -  First we will find out the reaction force developed at points A and D Then using the…

Q: Consider the beam shown. Suppose that M= 9 kip*ft, P=8 Kip,w=1.4 kip/ft and point D is located just…

A:

Q: Tutorial questions on shear stresses in beams subjected to non-uniform bending. Question One A…

A:

Q: The overhanging beam ABC in Figure supports a concentrated load and a uniformly distributed load.…

A:

Q: Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.